Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 125
Cisco TelePresence SX80 API Reference Guide
Provisioning commands
xCommand Provisioning CUCM CAPF OperationStart
Starts a pending CAPF (Certificate Authority Proxy Function) operation toward the CUCM. When the
CUCM administrator initiates an operation that the endpoint should perform (like installing, updating
or deleting certificates), this command can be used to start the CAPF operation.
AuthString: Set the authentication string required for the CAPF operation.
Requires user role: USER
Parameters:
AuthString: <S: 4, 10>
Example:
xCommand Provisioning CUCM CAPF OperationStart AuthString: 123456
xCommand Provisioning CUCM CTL Delete
Delete the stored CTL and ITL files (CTL: Certificate Trust List, ITL: Identity Trust List).
Requires user role: USER
Example:
xCommand Provisioning CUCM CTL Delete
xCommand Provisioning CUCM CTL Show
Shows the content of the installed Certificate Trust List file (CTL), if it exists. Each entry displayed
contains the information about one specific certificate. If a certificate has been deleted in CTL, it is
marked accordingly in the output.
Requires user role: USER
Example:
xCommand Provisioning CUCM CTL Show
xCommand Provisioning CUCM ExtensionMobility Login
Login command for the Extension Mobility service. You login to the Extension Mobility service with a
user name and pin. If there are multiple profiles available for that user, a separate event will be sent
with the available profiles for the user. A new login command with the profile can then be submitted.
Requires user role: USER
Parameters:
UserId(r): <S: 1, 255>
Pin(r): <S: 1, 255>
Profile: <S: 1, 255>
Example:
xCommand Provisoning CUCM ExtensionMobility Login UserId: user1 Pin: 1234
xCommand Provisioning CUCM ExtensionMobility Logout
This command will log you out of your Extension Mobility profile.
Requires user role: USER
Example:
xCommand Provisioning CUCM ExtensionMobility Logout
xCommand Provisioning CUCM ITL Show
Shows the content of the installed Identity Trust List file (ITL), if it exists. Each entry displayed
contains the information about one specific certificate. If a certificate has been deleted in CTL, it is
marked accordingly in the output.
Requires user role: USER
Example:
xCommand Provisioning CUCM ITL Show
xCommand Provisioning CompleteUpgrade
Starts installing the software upgrade if you wish to install it before it is set to do so.
Requires user role: USER
Example:
xCommand Provisioning CompleteUpgrade
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus
xCommand

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g