Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 55
Cisco TelePresence SX80 API Reference Guide
NetworkServices configuration
xConfiguration NetworkServices CDP Mode
Enable or disable the CDP (Cisco Discovery Protocol) daemon. Enabling CDP will make the endpoint
report certain statistics and device identifiers to a CDP-enabled switch. If CDP is disabled, the
Network VLAN Voice Mode: Auto setting will not work.
Requires user role: ADMIN
Value space: <Off/On>
Off: The CDP daemon is disabled.
On: The CDP daemon is enabled.
Example:
xConfiguration NetworkServices CDP Mode: On
xConfiguration NetworkServices H323 Mode
Determine whether the system should be able to place and receive H.323 calls or not.
Requires user role: ADMIN
Value space: <Off/On>
Off: Disable the possibility to place and receive H.323 calls.
On: Enable the possibility to place and receive H.323 calls (default).
Example:
xConfiguration NetworkServices H323 Mode: On
xConfiguration NetworkServices HTTP Mode
Set the HTTP mode to enable/disable access to the system through a web browser. The web
interface is used for system management, call management such as call transfer, diagnostics and
software uploads.
Requires user role: ADMIN
Value space: <Off/On>
Off: The HTTP protocol is disabled.
On: The HTTP protocol is enabled.
Example:
xConfiguration NetworkServices HTTP Mode: On
xConfiguration NetworkServices SIP Mode
Determine whether the system should be able to place and receive SIP calls or not.
Requires user role: ADMIN
Value space: <Off/On>
Off: Disable the possibility to place and receive SIP calls.
On: Enable the possibility to place and receive SIP calls (default).
Example:
xConfiguration NetworkServices SIP Mode: On
xConfiguration NetworkServices Telnet Mode
Telnet is a network protocol used on the Internet or Local Area Network (LAN) connections.
Requires user role: ADMIN
Value space: <Off/On>
Off: The Telnet protocol is disabled. This is the factory setting.
On: The Telnet protocol is enabled.
Example:
xConfiguration NetworkServices Telnet Mode: Off
xConfiguration NetworkServices WelcomeText
Choose which information the user should see when logging on to the codec through Telnet/SSH.
Requires user role: ADMIN
Value space: <Off/On>
Off: The welcome text is: Login successful
On: The welcome text is: Welcome to <system name>; Software version; Software release date;
Login successful.
Example:
xConfiguration NetworkServices WelcomeText: On
xConfiguration NetworkServices XMLAPI Mode
Enable or disable the video system's XML API. For security reasons this may be disabled. Disabling
the XML API will limit the remote manageability with for example TMS, which no longer will be able
to connect to the video system.
Requires user role: ADMIN
Value space: <Off/On>
Off: The XML API is disabled.
On: The XML API is enabled (default).
Example:
xConfiguration NetworkServices XMLAPI Mode: On
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus
xConfiguration

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g