Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 65
Cisco TelePresence SX80 API Reference Guide
SIP configuration
xConfiguration SIP ANAT
ANAT (Alternative Network Address Types) enables media negotiation for multiple addresses and
address types, as specified in RFC 4091.
Requires user role: ADMIN
Value space: <Off/On>
Off: Disable ANAT.
On: Enable ANAT.
Example:
xConfiguration SIP ANAT: Off
xConfiguration SIP AuthenticateTransferror
Not applicable in this version.
xConfiguration SIP ListenPort
Turn on or off the listening for incoming connections on the SIP TCP/UDP ports. If turned off, the
endpoint will only be reachable through the SIP registrar (CUCM or VCS). It is recommended to
leave this setting at its default value.
Requires user role: ADMIN
Value space: <Off/On>
Off: Listening for incoming connections on the SIP TCP/UDP ports is turned off.
On: Listening for incoming connections on the SIP TCP/UDP ports is turned on.
Example:
xConfiguration SIP ListenPort: On
xConfiguration SIP PreferredIPMedia
Define the preferred IP version for sending and receiving media (audio, video, data). Only applicable
when both Network IPStack and Conference CallProtocolIPStack are set to Dual, and the network
does not have a mechanism for choosing the preferred IP version.
Requires user role: ADMIN
Value space: <IPv4/IPv6>
IPv4: The preferred IP version for media is IPv4.
IPv6: The preferred IP version for media is IPv6.
Example:
xConfiguration SIP PreferredIPMedia: IPv4
xConfiguration SIP PreferredIPSignaling
Define the preferred IP version for signaling (audio, video, data). Only applicable when both Network
IPStack and Conference CallProtocolIPStack are set to Dual, and the network does not have a
mechanism for choosing the preferred IP version. It also determines the priority of the A/AAAA
lookups in DNS, so that the preferred IP version is used for registration.
Requires user role: ADMIN
Value space: <IPv4/IPv6>
IPv4: The preferred IP version for signaling is IPv4.
IPv6: The preferred IP version for signaling is IPv6.
Example:
xConfiguration SIP PreferredIPSignaling: IPv4
xConfiguration SIP OCSP Mode
Not applicable in this version.
xConfiguration SIP OCSP DefaultResponder
Not applicable in this version.
xConfiguration SIP Profile [1..1] Ice Mode
ICE (Interactive Connectivity Establishment, RFC 5245) is a NAT traversal solution that the endpoints
can use to discover the optimized media path. Thus the shortest route for audio and video is always
secured between the endpoints. NOTE: ICE is not supported when registered to CUCM (Cisco
Unified Communication Manager).
Requires user role: ADMIN
Value space: <Auto/Off/On>
Auto: When set to Auto, ICE will be enabled if a turn server is provided, otherwise ICE will be
disabled.
Off: Set to Off to disable ICE.
On: Set to On to enable ICE.
Example:
xConfiguration SIP Profile 1 Ice Mode: Auto
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus
xConfiguration

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g