Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 82
Cisco TelePresence SX80 API Reference Guide
xConfiguration Video Output Connector [1..3] Resolution
Set the resolution and refresh rate for the connected screen.
Requires user role: ADMIN
Value space: <Auto/1280_720_50/1280_720_60/1920_1080_50/1920_1080_60>
Auto: The system will automatically try to set the optimal resolution based on negotiation with the
connected monitor.
1280_720_50: The resolution is 1280 x 720, and the refresh rate is 50 Hz.
1280_720_60: The resolution is 1280 x 720, and the refresh rate is 60 Hz.
1920_1080_50: The resolution is 1920 x 1080, and the refresh rate is 50 Hz.
1920_1080_60: The resolution is 1920 x 1080, and the refresh rate is 60 Hz.
Example:
xConfiguration Video Output Connector 2 Resolution: Auto
xConfiguration Video Output Connector [1..3] MonitorRole
The monitor role describes which video streams will be shown on the monitor connected to this
video output connector. Together the Video Monitors setting and the MonitorRole settings for all
outputs define which layout (video streams) will be shown on each monitor.
Requires user role: ADMIN
Value space: <Auto/First/Second/Third/PresentationOnly/Recorder>
Auto: The system will detect when a monitor is connected, and a monitor role (First, Second,
Third) that corresponds with the Video Monitors setting will be assigned automatically.
First/Second/Third: Define the role of the monitor in a multi-monitor setup. In a single-monitor
setup, there is no difference between First, Second and Third.
PresentationOnly: Show presentation video stream if active, and nothing else. Monitors/outputs
with this monitor role are disregarded by the Video Monitors setting.
Recorder: Show all participants, including the local main video (self-view). If active, also show
the presentation. Monitors/outputs with this monitor role are disregarded by the Video Monitors
setting.
Example:
xConfiguration Video Output Connector 1 MonitorRole: Auto
xConfiguration Video WallPaper
This has been replaced with the UserInterface Wallpaper setting.
Experimental configuration
The Experimental settings are for testing only and should not be used unless agreed with Cisco.
These settings are not documented and WILL change in later releases.
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus
xConfiguration

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g