Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 156
Cisco TelePresence SX80 API Reference Guide
xStatus Call [n] FacilityServiceId
When calling a facility service, the facility service id is shown. Otherwise the value 0 is returned.
Value space of the result returned:
<0..5>
Example:
xStatus Call FacilityServiceId
*s Call 3 FacilityServiceId: 1
** end
xStatus Call [n] Encryption Type
Shows the encryption type of the call. You can run the command xStatus Call to find the call
identity.
Value space of the result returned:
< "N o n e "/ "A e s -12 8 ">
Example:
xStatus Call 27 Encryption Type
*s Call 27 Encryption Type: "None"
** end
xStatus Call [n] PlacedOnHold
Shows the placed on hold status of the call. You can run the command xStatus Call to find the call
identity.
Value space of the result returned:
<True/False>
Example:
xStatus Call 27 PlacedOnHold
*s Call 27 PlacedOnHold: False
** end
xStatus Call [n] Duration
Shows the duration of a call (in seconds). You can run the command xStatus Call to find the call
identity.
Value space of the result returned:
<Integer>
Example:
xStatus Call 27 Duration
*s Call 27 Duration: 2354
** end
xStatus Call [n] SecurityStatus
Security status of a call represents the least of the security statuses of all the endpoints involved in
a CUCM call.
Value space of the result returned:
<Invalid/Unknown/NotAuthenticated/Authenticated>
xStatus Call [n] AnswerState
Indicates if a call is answered, ignored or has been automatically answered by a system.
Value space of the result returned:
<Unanswered/Ignored/Autoanswered/Answered>
Example:
xStatus Call AnswerState
*s Call 5 AnswerState: Answered
** end
xStatus Call [n] ModifyState
Shows the current state of a pending Call Modify operation. Not in use in this software version.
OutgoingModify: a request CallEscalate to Video is pending.
IncomingModify: a peer has requested to escalate the call to Video.
Idle: No Call Modify operation is pending.
Value space of the result returned:
<Idle/Outgoing/Incoming>
Example:
xStatus Call ModifyState
*s Call 11 ModifyState: Idle
** end
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatusxStatus

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g