EasyManuals Logo

Cisco TelePresence SX80 User Manual

Cisco TelePresence SX80
231 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #48 background imageLoading...
Page #48 background image
D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 48
Cisco TelePresence SX80 API Reference Guide
Logging configuration
xConfiguration Logging Mode
Not applicable in this version.
Network configuration
xConfiguration Network [1..1] IPStack
Select if the system should use IPv4, IPv6, or dual IP stack, on the network interface. NOTE: After
changing this setting you may have to wait up to 30 seconds before it takes effect.
Requires user role: ADMIN
Value space: <Dual/IPv4/IPv6>
Dual: When set to Dual, the network interface can operate on both IP versions at the same time,
and can have both an IPv4 and an IPv6 address at the same time.
IPv4: When set to IPv4, the system will use IPv4 on the network interface.
IPv6: When set to IPv6, the system will use IPv6 on the network interface.
Example:
xConfiguration Network 1 IPStack: Dual
xConfiguration Network [1..1] IPv4 Assignment
Define how the system will obtain its IPv4 address, subnet mask and gateway address. This setting
only applies to systems on IPv4 networks.
Requires user role: ADMIN
Value space: <Static/DHCP>
Static: The addresses must be configured manually using the Network IPv4 Address, Network
IPv4 Gateway and Network IPv4 SubnetMask settings (static addresses).
DHCP: The system addresses are automatically assigned by the DHCP server.
Example:
xConfiguration Network 1 IPv4 Assignment: DHCP
xConfiguration Network [1..1] IPv4 Address
Enter the static IPv4 network address for the system. This setting is only applicable when Network
Assignment is set to Static.
Requires user role: ADMIN
Value space: <S: 0, 64>
Format: A valid IPv4 address.
Example:
xConfiguration Network 1 IPv4 Address: "192.0.2.2"
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus
xConfiguration

Table of Contents

Other manuals for Cisco TelePresence SX80

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco TelePresence SX80 and is the answer not in the manual?

Cisco TelePresence SX80 Specifications

General IconGeneral
Maximum frame rate60 fps
Supported video modes720p, 1080p
Video formats supportedH.261, H.262, H.263, H.264, H.265
Supported graphics resolutions1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecsG.711, G.722, G.722.1, G.729ab
Noise reductionYes
HDMI ports quantity5
DVI-D ports quantity1
USB 2.0 ports quantity2
Product colorSilver
Rack capacity1U
Number of persons0 person(s)
Analog signal format systemNTSC, PAL
Security algorithmsHTTPS, SSH
Ethernet LAN data rates10, 100, 1000 Mbit/s
Supported network protocolsSIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Storage temperature (T-T)-20 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 90 %
Sensor type-
Image sensor size- \
Weight and Dimensions IconWeight and Dimensions
Depth309.8 mm
Width442 mm
Height44 mm
Weight3650 g

Related product manuals