Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 54
Cisco TelePresence SX80 API Reference Guide
xConfiguration Network [1..1] TrafficControl Mode
Set the network traffic control mode to decide how to control the video packets transmission speed.
Requires user role: ADMIN
Value space: <Off/On>
Off: Transmit video packets at link speed.
On: Transmit video packets at maximum 20 Mbps. Can be used to smooth out bursts in the outgo-
ing network traffic.
Example:
xConfiguration Network 1 TrafficControl: On
xConfiguration Network [1..1] RemoteAccess Allow
Define which IP addresses (IPv4/IPv6) are allowed for remote access to the codec from SSH/
Telnet/HTTP/HTTPS. Multiple IP addresses are separated by a white space.
A network mask (IP range) is specified by <ip address>/N, where N is 1-32 for IPv4, and N is 1-128
for IPv6. The /N is a common indication of a network mask where the first N bits are set. Thus
192.168.0.0/24 would match any address starting with 192.168.0, since these are the first 24 bits in
the address.
Requires user role: ADMIN
Value space: <S: 0, 255>
Format: String with a maximum of 255 characters.
Example:
xConfiguration Network 1 RemoteAccess Allow: "10.11.2.3 192.168.0.0/24
2001:0db8:0000:0000:0000:ff00:0042:8329 2001:db8:abcd:0012::0/64"
xConfiguration Network [1..1] VLAN Voice Mode
Set the VLAN voice mode. The VLAN Voice Mode will be set to Auto automatically if you have Cisco
UCM (Cisco Unified Communications Manager) as provisioning infrastructure. Note that Auto mode
will NOT work if the NetworkServices CDP Mode setting is Off.
Requires user role: ADMIN
Value space: <Auto/Manual/Off>
Auto: The Cisco Discovery Protocol (CDP), if available, assigns an id to the voice VLAN. If CDP is
not available, VLAN is not enabled.
Manual: The VLAN ID is set manually using the Network VLAN Voice VlanId setting. If CDP is avail-
able, the manually set value will be overruled by the value assigned by CDP.
Off: VLAN is not enabled.
Example:
xConfiguration Network 1 VLAN Voice Mode: Auto
xConfiguration Network [1..1] VLAN Voice VlanId
Set the VLAN voice ID. This setting will only take effect if VLAN Voice Mode is set to Manual.
Requires user role: ADMIN
Value space: <1..4094>
Range: Select a value between 1 and 4094.
Example:
xConfiguration Network 1 VLAN Voice VlanId: 1
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus
xConfiguration

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g