EasyManuals Logo

Cisco TelePresence SX80 User Manual

Cisco TelePresence SX80
231 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #118 background imageLoading...
Page #118 background image
D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 118
Cisco TelePresence SX80 API Reference Guide
xCommand Peripherals Pairing DeviceDiscovery Start
Start device discovery to detect ISDN Links in the same network.
AutoPairing: You can select to automatically pair the detected device to the endpoint.
DeviceType: Only look for ISDN Link.
Timeout: Set a maximum time for the search from 3 to 60 seconds.
Requires user role: ADMIN
Parameters:
AutoPairing: <On, Off>
DeviceType: <ISDNLink>
Timeout: <3..60>
Example:
xCommand Peripherals Pairing DeviceDiscovery Start
xCommand Peripherals Pairing Pair
Pair an ISDN Link to an endpoint.
MacAddress: Enter the MAC address for the ISDN Link you wish to pair to the endpoint.
Requires user role: ADMIN
Parameters:
MacAddress(r): <S: 1, 1450>
Example:
xCommand Peripherals Pairing Pair MacAddress: 1.2.3.4
xCommand Peripherals Pairing Unpair
Unpair endpoint from an ISDN Link, when the two have contact.
MacAddress: Enter the MAC address for the ISDN Link you wish to unpair from the endpoint.
Requires user role: ADMIN
Parameters:
MacAddress(r): <S: 1, 100>
Example:
xCommand Peripherals Pairing Unpair MacAddress: 1.2.3.4
xCommand Peripherals Pairing Purge
Force unpair an endpoint from an ISDN Link when a connection has been lost. Note: You must also
unpair the ISDN Link to be able to pair it to another endpoint.
Requires user role: ADMIN
Parameters:
ID(r): <S: 1, 100>
Example:
xCommand Peripherals Purge ID: 1.2.3.4
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus
xCommand

Table of Contents

Other manuals for Cisco TelePresence SX80

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco TelePresence SX80 and is the answer not in the manual?

Cisco TelePresence SX80 Specifications

General IconGeneral
Maximum frame rate60 fps
Supported video modes720p, 1080p
Video formats supportedH.261, H.262, H.263, H.264, H.265
Supported graphics resolutions1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecsG.711, G.722, G.722.1, G.729ab
Noise reductionYes
HDMI ports quantity5
DVI-D ports quantity1
USB 2.0 ports quantity2
Product colorSilver
Rack capacity1U
Number of persons0 person(s)
Analog signal format systemNTSC, PAL
Security algorithmsHTTPS, SSH
Ethernet LAN data rates10, 100, 1000 Mbit/s
Supported network protocolsSIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Storage temperature (T-T)-20 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 90 %
Sensor type-
Image sensor size- \
Weight and Dimensions IconWeight and Dimensions
Depth309.8 mm
Width442 mm
Height44 mm
Weight3650 g

Related product manuals