Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 140
Cisco TelePresence SX80 API Reference Guide
xCommand Video PictureLayoutSet
Select the screen layout mode.
Target: Select if the target is the local layout or the remote layout.
CallId: The CallID is returned when the xCommand Dial command is run. During the call you can run
the xStatus Call command to see the CallId.
LayoutFamily: Select a layout family.
CustomLayoutName: Enter a name for the layout.
Requires user role: USER
Parameters:
Target: <local/remote>
CallId: <0..65534>
LayoutFamily(r): <auto/custom/equal/fullscreen/overlay/presentationlargespeaker/
presentationsmallspeaker/prominent/single/speaker_full>
CustomLayoutName: <S: 1, 128>
Example:
xCommand Video PictureLayoutSet Target: Local LayoutFamily: equal
xCommand Video PreviewFilmstrip Set
Moves the location of the filmstrip associated with the layouts used in presentation preview mode.
Not in use in this software version.
LowerCenter: The preview appears on the bottom of the screen, in center.
LowerLeft: The preview appears in the lower left corner of the screen.
LowerRight: The preview appears in the lower right corner of the screen.
UpperCenter: The preview appears on top of the screen, in center.
UpperLeft: The preview appears in the upper left corner of the screen.
UpperRight: The preview appears in the upper right corner of the screen.
Requires user role: ADMIN
Parameters:
Position(r): <LowerCenter/LowerLeft/LowerRight/UpperCenter/UpperLeft/UpperRight>
Example:
xCommand Video PreviewFilmstrip Set Position: LowerCenter
xCommand Video Selfview Set
Sets self-view on/off and specifies its size and position. If the parameter is not specified, current
value is used.
Mode: Selfview on/off
FullscreenMode: Self-view in fullscreen or pip.
PIPPosition: Predefined PIP positions.
FullscreenMode: Choose between displaying the self-view in full screen or not.
PIPPosition: Select the position for the self-view image.
CenterLeft: The self-view PiP appears on the left side of the screen, in center.
CenterRight: The self-view PiP appears on the right side of the screen, in center.
LowerLeft: The self-view PiP appears in the lower left corner of the screen.
LowerRight: The self-view PiP appears in the lower right corner of the screen.
UpperCenter: The self-view PiP appears on top of the screen, in center.
UpperLeft: The self-view PiP appears in the upper left corner of the screen.
UpperRight: The self-view PiP appears in the upper right corner of the screen.
OnMonitorRole: Displays self-view on monitors with this role.
Requires user role: ADMIN
Parameters:
Mode: <On/Off>
FullscreenMode: <On/Off>
PIPPosition: <CenterLeft/CenterRight/LowerLeft/LowerRight/UpperCenter/UpperLeft/
UpperRight>
OnMonitorRole: <First/Fourth/Second/Third>
Example:
Example 1
xCommand Video Selfview Set Mode: On FullscreenMode: Off PIPPosition:
CenterLeft OnMonitorRole: First
Example 2
xCommand Video Selfview Set FullscreenMode: On OnMonitorRole: Second
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus
xCommand

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g