Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 34
Cisco TelePresence SX80 API Reference Guide
xConfiguration Audio Input Microphone [1..8] Type
The microphone connectors are intended for electret type microphones. The microphone connector
can be set to line or microphone mode.
Requires user role: ADMIN
Value space: <Microphone/Line>
Microphone: Select Microphone when you have 48 V Phantom voltage and the pre-amplification
is On.
Line: Select Line when you have a standard balanced line input. The phantom voltage and
pre-amplification is Off.
Example:
xConfiguration Audio Input Microphone 1 Type: Line
xConfiguration Audio Output HDMI [1..2] Level
Define the output level of the HDMI output connector, in steps of 1 dB.
Requires user role: ADMIN
Value space: <-24..0>
Range: Select a value between -24 and 0, in steps of 1 dB.
Example:
xConfiguration Audio Output HDMI 1 Level: 0
xConfiguration Audio Output HDMI [1..2] Mode
Determine if the audio channel on the HDMI output connector shall be enabled.
Requires user role: ADMIN
Value space: <Off/On>
Off: Disable the audio channel on the HDMI output.
On: Enable the audio channel on the HDMI output.
Example:
xConfiguration Audio Output HDMI 1 Mode: On
xConfiguration Audio Output Line [1..6] Channel
Define whether the Audio Line output is a mono signal or part of a multichannel signal.
Requires user role: ADMIN
Value space: <Right/Left/Mono>
Right: The Audio Line output signal is the right channel of a stereo signal.
Left: The Audio Line output signal is the left channel of a stereo signal.
Mono: The Audio Line output signal is a mono signal.
Example:
xConfiguration Audio Output Line 1 Channel: left
xConfiguration Audio Output Line [1..6] Equalizer ID
Select the audio output line equalizer ID.
Requires user role: ADMIN
Value space: <1..8>
Range: Select EqualizerID 1 to 8.
Example:
xConfiguration Audio Output Line 1 Equalizer ID: 1
xConfiguration Audio Output Line [1..6] Equalizer Mode
Set the audio output line equalizer mode.
Requires user role: ADMIN
Value space: <Off/On>
Off: No equalizer.
On: Enable the equalizer for the audio output line.
Example:
xConfiguration Audio Output Line 1 Equalizer Mode: Off
xConfiguration Audio Output Line [1..6] Level
Define the audio level on the line output connector.
See the Audio Level table in the Physical Interface Guide for the codec for a complete overview of
the menu values represented in dB.
Requires user role: ADMIN
Value space: <-24..0>
Range: Select a value between -24 and 0, in steps of 1 dB.
Example:
xConfiguration Audio Output Line 1 Level: -10
xConfiguration Audio Output Line [1..6] Mode
Set the audio output line mode.
Requires user role: ADMIN
Value space: <Off/On>
Off: Disable the Audio Line output.
On: Enable the Audio Line output.
Example:
xConfiguration Audio Output Line 1 Mode: On
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus
xConfiguration

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g