Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 68
Cisco TelePresence SX80 API Reference Guide
xConfiguration SIP Profile [1..1] Proxy [1..4] Discovery
Select if the SIP Proxy address is to be obtained manually or by using Dynamic Host Configuration
Protocol (DHCP).
Requires user role: ADMIN
Value space: <Auto/Manual>
Auto: When Auto is selected, the SIP Proxy address is obtained using Dynamic Host Configuration
Protocol (DHCP).
Manual: When Manual is selected, the manually configured SIP Proxy address will be used.
Example:
xConfiguration SIP Profile 1 Proxy 1 Discovery: Manual
xConfiguration SIP Profile [1..1] Type
Enables SIP extensions and special behavior for a vendor or provider.
Requires user role: ADMIN
Value space: <Standard/Cisco>
Standard: Use this when registering to standard SIP Proxy (tested with Cisco TelePresence VCS
and Broadsoft)
Cisco: Use this when registering to Cisco Unified Communication Manager.
Example:
xConfiguration SIP Profile 1 Type: Standard
xConfiguration SIP Profile [1..1] Mailbox
When registered to a Cisco Unified Communications Manager (CUCM) you may be offered the
option of having a private voice mailbox. Enter the number (address) of the mailbox in this setting, or
leave the string empty if you do not have a voice mailbox.
Requires user role: ADMIN
Value space: <S: 0, 255>>
Format: String with a maximum of 255 characters.
Example:
xConfiguration SIP Profile 1 Mailbox: "12345678"
xConfiguration SIP Profile [1..1] Line
When registered to a Cisco Unified Communications Manager (CUCM) the endpoint may be part
of a shared line. This means that several devices share the same directory number. The different
devices sharing the same number receive status from the other appearances on the line as defined
in RFC 4235.
Note that shared lines are set up by CUCM, not by the endpoint. Therefore do not change this
setting manually; CUCM pushes this information to the endpoint when required.
Requires user role: ADMIN
Value space: <Private/Shared>
Shared: The system is part of a shared line and is therefore sharing its directory number with other
devices.
Private: This system is not part of a shared line (default).
Example:
xConfiguration SIP Profile 1 Line: Private
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus
xConfiguration

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g