Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 79
Cisco TelePresence SX80 API Reference Guide
xConfiguration Video PIP ActiveSpeaker DefaultValue Position
Determine the position on screen of the active speaker picture-in-picture (PiP). The setting only
takes effect when using a video layout where the active speaker is a PiP, i.e. the Overlay layout, or
possibly a Custom layout (see the Video Layout LocalLayoutFamily setting). The setting takes effect
from the next call onwards; if changed during a call, it will have no effect on the current call.
Requires user role: ADMIN
Value space: <Current/UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/LowerLeft/
LowerRight>
Current: The position of the active speaker PiP will be kept unchanged when leaving a call.
UpperLeft: The active speaker PiP will appear in the upper left corner of the screen.
UpperCenter: The active speaker PiP will appear in the upper center position.
UpperRight: The active speaker PiP will appear in the upper right corner of the screen.
CenterLeft: The active speaker PiP will appear in the center left position.
CentreRight: The active speaker PiP will appear in the center right position.
LowerLeft: The active speaker PiP will appear in the lower left corner of the screen.
LowerRight: The active speaker PiP will appear in the lower right corner of the screen.
Example:
xConfiguration Video PIP ActiveSpeaker DefaultValue Position: Current
xConfiguration Video PIP Presentation DefaultValue Position
Determine the position on screen of the presentation picture-in-picture (PiP). The setting only takes
effect when the presentation is explicitly minimized to a PiP, for example using the Touch controller.
The setting takes effect from the next call onwards; if changed during a call, it will have no effect on
the current call.
Requires user role: ADMIN
Value space: <Current/UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/LowerLeft/
LowerRight>
Current: The position of the presentation PiP will be kept unchanged when leaving a call.
UpperLeft: The presentation PiP will appear in the upper left corner of the screen.
UpperCenter: The presentation PiP will appear in the upper center position.
UpperRight: The presentation PiP will appear in the upper right corner of the screen.
CenterLeft: The presentation PiP will appear in the center left position.
CentreRight: The presentation PiP will appear in the center right position.
LowerLeft: The presentation PiP will appear in the lower left corner of the screen.
LowerRight: The presentation PiP will appear in the lower right corner of the screen.
Example:
xConfiguration Video PIP Presentation DefaultValue Position: Current
xConfiguration Video SelfviewDefault Mode
Determine if the main video source (self-view) shall be displayed on screen after a call. The position
and size of the self-view window is determined by the Video SelfviewDefault PIPPosition and the
Video SelfviewDefault FullscreenMode settings respectively.
Requires user role: ADMIN
Value space: <Off/Current/On>
Off: self-view is switched off when leaving a call.
Current: self-view is left as is, i.e. if it was on during the call, it remains on after the call; if it was off
during the call, it remains off after the call.
On: self-view is switched on when leaving a call.
Example:
xConfiguration Video SelfviewDefault Mode: Current
xConfiguration Video SelfviewDefault FullscreenMode
Determine if the main video source (self-view) shall be shown in full screen or as a small picture-in-
picture (PiP) after a call. The setting only takes effect when self-view is switched on (see the Video
SelfviewDefault Mode setting).
Requires user role: ADMIN
Value space: <Off/Current/On>
Off: self-view will be shown as a PiP.
Current: The size of the self-view picture will be kept unchanged when leaving a call, i.e. if it was
a PiP during the call, it remains a PiP after the call; if it was fullscreen during the call, it remains
fullscreen after the call.
On: The self-view picture will be shown in fullscreen.
Example:
xConfiguration Video SelfviewDefault FullscreenMode: Current
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus
xConfiguration

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g