EasyManuals Logo

Curtiss-Wright CHAMP-AV8 User Manual

Default Icon
166 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #100 background imageLoading...
Page #100 background image
CURTISS-WRIGHT 1
826448 VERSION 5 MARCH 2015 PROPRIETARY A-9
VITA 46 P1 Fabric
Connector
The P1 connector on the CHAMP-AV8 supports the following functions/interfaces:
V46 Fabric Connections (Four 4x Ports)
Reserved Bus (BP_GDISCRETE1) signal
VITA 46 and CHAMP-AV8 System Signals (SYSCON_L, CARD_FAIL_L, PB_RESET_L)
Nominal 3V battery connection (VBAT)
No Connect (NC) Signals (NC_RFU, NC_IO_RSRV)
See “CHAMP-AV8 P1 (SRIO Fabric) Connector Pin Assignments” on page A-17 for additional
details.
VITA 46 P2 PCIe
Expansion
Connector
The P2 connector on the CHAMP-AV8 supports the following functions/interfaces:
PCIe expansion plane - supports up to two eight-lane PCIe ports (see Table 1.1,
“XMC/Expansion Plane Interface Build-Time Options for PCIe, on page 1-8 for details).
See “CHAMP-AV8 P2 (PCIe Expansion) Connector Pin Assignments” on page A-20 for
additional details.
VITA 46 P3 XMC
Site’s PMC User
I/O Connector
The P3 connector on the CHAMP-AV8 supports the following functions/interfaces:
Utilized for XMC J14 user I/O as per the VITA 46.9 P64s pattern.
No Connect (NC) Signals
See “Corresponding VPX Backplane J2 (PCIe Expansion) Connector Pin Assignments” on page
A-22 for additional details.
VITA 46 P4
Basecard I/O
Connector
The P4 connector on the CHAMP-AV8 supports the following functions/interfaces:
CHAMP-AV8 JTAG Selection Signals (JTSEL_L, JPROC[3:0])
Reset/Power Sequencer/JTAG CPLD JTAG Chain Signals
CHAMP-AV8 Backplane Jumper Signals
CHAMP-AV8 EIA-422/485 Serial Ports (RS422_[A2/B2] TX/RX)
CHAMP-AV8 EIA-232 Serial Ports (RS232_[A0/A1/B0/B1] TX/RX)
1000Base-T Ports (ETH[A/B]_TRX[0:3])
1000Base-BX Ports (UTP[A/B] TX/RX)
See “CHAMP-AV8 P4 (Basecard I/O) Connector Pin Assignments” on page A-26 for additional
details.
VITA 46 P5 XMC
User I/O Connector
The P5 connector on the CHAMP-AV8 supports the following functions/interfaces:
XMC Site Single Ended User I/O (38 signals) from XMC J16 connector (XMC_C[19:01]
and XMC_F[19:01])
XMC Site Differential User I/O (8 of the 20 pairs) from XMC J16 connector
(XMC_DP[03:00] and XMC_DP[13:10])
See “CHAMP-AV8 P5 (XMC User I/O) Connector Pin Assignments” on page A-30 for additional
details.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Curtiss-Wright CHAMP-AV8 and is the answer not in the manual?

Curtiss-Wright CHAMP-AV8 Specifications

General IconGeneral
BrandCurtiss-Wright
ModelCHAMP-AV8
CategorySignal Processors
LanguageEnglish