Det-Tronics Eagle Quantum Premier - Default Chapter; Table of Contents

Table of Contents
Section 1 - Safety
ALERT MESSAGES ...................................................... 1-1
Section 2 - Introduction
SYSTEM DESCRIPTION .............................................. 2-1
Communications Loop ................................................... 2-1
LON Communication Heartbeat ..................................... 2-2
Theory of Operation ....................................................... 2-3
Controller Logs ............................................................... 2-4
Controller User Logic ..................................................... 2-4
Communication Network Fault Operation ...................... 2-5
Multiple Wiring Faults ..................................................... 2-5
SIL2 Capable System ..................................................... 2-5
MAJOR COMPONENT DESCRIPTIONS .....................2-6
System Controller ........................................................... 2-6
Controller Redundancy ............................................... 2-6
Ethernet Interface Board ............................................. 2-7
Serial Interface Board ................................................. 2-7
EQP RS-485 Surge Protector ...................................... 2-7
ControlNet Board or EtherNet DLR Board ................... 2-7
Controller-to-Controller Communication ...................... 2-8
EQP Marine Application System ................................. 2-8
Local Operating Network (LON)..................................... 2-8
Network Extenders ...................................................... 2-8
EQ21xxPS Series Power Supplies and
EQ2100PSM Power Supply Monitor ............................ 2-9
EQP21xxPS(–X) Power Supplies and
EQP2410PS(–P) Converter .......................................... 2-9
EQ2220GFM Ground Fault Monitor ............................. 2-9
Field Devices .................................................................. 2-9
Flame Detectors .......................................................... 2-9
EQ2200 UVHT + C7050 Detector ............................... 2-9
Model HD Heat Detector ............................................. 2-9
U5015 Explosion-Proof Smoke Detector ................... 2-10
X7050 xWatch Explosion-Proof Camera....................2-10
EQ3730EDIO Enhanced Discrete I/O Module .......... 2-10
EQ3700 8 Channel DCIO Module ............................. 2-11
EQ3720 8 Channel Relay Module ............................. 2-11
EQ3710AIM Analog Input Module............................. 2-12
EQ3770 Explosion-Proof I/O (EIO) Module ............... 2-12
EQ3760ASM Addressable Smoke and Heat Module ...2-13
EQ3750ASH Addressable Smoke and Heat Module ... 2-13
EQ22xxARM Agent Release Module......................... 2-14
EQ22xxSAM Signal Audible Module ......................... 2-15
EQ22xxIDC Series Initiating Device Circuit ............... 2-15
UD10 DCU Emulator ................................................. 2-16
EQ22xxDCU and EQ22xxDCUEX
Digital Communication Units ..................................... 2-16
PIRECL PointWatch Eclipse ......................................2-17
LS2000 Line-of-Sight ................................................. 2-17
EQ3900 Enclosure Solutions ..................................... 2-17
EQ3900RPS Explosion-Proof Power Supply ............. 2-17
Section 3 - Installation
SAFETY SYSTEM DESIGN REQUIREMENTS ............. 3-1
Identifying the Area of Protection ...................................3-1
Identifying Wiring, Network (LON),
and System Power Requirements .................................. 3-1
General Wiring Requirements ..................................... 3-1
Power Wiring ............................................................... 3-1
System Wiring (ATEX and IECEx) ................................ 3-1
Determining Power Requirements............................... 3-3
EQ211xPS, EQ213xPS and EQ217xPS
Power Supplies ........................................................... 3-5
Backup Battery ............................................................ 3-5
Battery Charger ........................................................... 3-5
EQP21x0PS(–X) Power Supplies ................................. 3-5
EQP2410PS(–P) Converter .......................................... 3-6
Determining Power Requirements............................... 3-6
Shield Grounding ........................................................ 3-7
Junction Box Grounding.............................................. 3-7
Response Time vs. System Size ................................. 3-7
Moisture Damage Protection ....................................... 3-7
Electrostatic Discharge ............................................... 3-7
GROUND FAULT MONITOR (GFM) INSTALLATION ......3-8
Mounting......................................................................... 3-8
Wiring ............................................................................ 3-8
NETWORK & NETWORK EXTENDER INSTALLATION ... 3-8
Mounting......................................................................... 3-8
Wiring ............................................................................ 3-8
EQ3XXX CONTROLLER INSTALLATION ................. 3-10
Enclosure Requirements ..............................................3-10
Mounting....................................................................... 3-11
Serial Interface Board................................................... 3-11
Ethernet Interface Board .............................................. 3-11
Wiring .......................................................................... 3-11
Power Wiring ............................................................. 3-11
Electrical Connections .............................................. 3-11
Controller to Controller Communication .......................3-16
Configuration ................................................................ 3-20
Software Defined Addresses .....................................3-20
EQ3XXX REDUNDANT CONTROLLER
INSTALL ATION ..........................................................3-22
Enclosure Requirements ..............................................3-22
Mounting....................................................................... 3-22
Wiring .......................................................................... 3-22
LON Wiring ................................................................... 3-22
High Speed Serial Link (HSSL) .................................... 3-23
Configuration ................................................................ 3-23
S
³
Configuration ......................................................... 3-23
Controller Addresses ................................................. 3-23
RS-485/RS-232 .......................................................... 3-23
ControlNet ................................................................. 3-23
EtherNet DLR ............................................................ 3-23