Table of Contents
Service Instructions 867-M PREMIUM - 03.0 - 05/2017 3
19.2.3 Disassembling the encoder ...................................................... 93
19.2.4 Disassembling the stator .......................................................... 94
19.2.5 Disassembling the rotor............................................................ 94
19.3 Assembling the drive ................................................................ 95
19.3.1 Assembling the rotor................................................................. 95
19.3.2 Assembling the stator ............................................................... 96
19.3.3 Assembling the encoder ........................................................... 97
19.3.4 Assembling the cover ............................................................... 97
19.3.5 Locking the machine in place ................................................... 98
19.3.6 Assembling the handwheel flange............................................ 98
19.3.7 Assembling the handwheel....................................................... 99
20 Programming ........................................................................ 101
20.1 Calling up the Technician level............................................... 101
20.2 Structure of the software......................................................... 101
20.3 Parameter selection (ParameterCall) submenu............... 102
20.4 Program presettings (Default Program) submenu........... 103
20.4.1 Setting the stitch length (Stitchlen.) parameter................ 103
20.4.2 Setting the foot pressure (Foot Press.) parameter............ 104
20.4.3 Setting the needle thread tension (Thr.Tens.) parameter... 104
20.4.4 Setting the sewing foot stroke (Foot Stroke) parameter.... 104
20.4.5 Setting the Start bartack parameter (Start Tack)............... 105
20.4.6 Set End bartack parameter (End Tack)................................ 105
20.4.7 Setting the Thread cutter parameter (Thread Trim)............ 105
20.4.8 Setting the daily piece counter (DailyPieces) parameter... 105
20.5 Machine configuration (Machine config.) submenu......... 106
20.5.1 Setting the Thread cutter parameter (Thread Trim)............ 107
20.5.2 Setting the Thread clamp parameter (Thread Clamp)......... 108
20.5.3 Setting the Speed (Speed) parameter.................................... 110
20.5.4 Setting the Stop positions (Stop Positions) parameter.... 110
20.5.5 Setting the Sewing foot (Foot) parameter ............................. 110
20.5.6 Setting the needle thread tension (Thr.Tens.) parameter... 111
20.5.7 Setting the sewing foot stroke (Stroke) parameter............... 112
20.5.8 Setting the stitch length (Stitchlen.) parameter................ 113
20.5.9 Setting the Bobbin (Bobbin) parameter................................. 113
20.5.10 Setting Motor holding force (Holding Force) parameter.... 114
20.5.11 Setting the Pedal (Pedal) parameter..................................... 114
20.5.12 Setting the Needle cooling (NeedleCooling) parameter..... 115
20.5.13 Setting the Seam center guide (CenterGuide) parameter... 115
20.5.14 Setting the Edge guide (EdgeGuide) parameter ................... 116
20.5.15 Setting the Material thickness detection
(Fabric Thickness) parameter ......................................... 116
20.5.16 Setting the Correction of effects of high speed
(Speed Corr) parameter ...................................................... 117
20.5.17 Setting the light barrier (LightBarrier) parameter............. 117
20.5.18 Setting the Segment length (Mode Seg.Size) parameter.... 118
20.5.19 Setting the Threading mode (Threading) parameter ........... 118
2
0.6 User configuration (User config.) submenu...................... 118
20.6.1 Setting the Language selection (Language) parameter ........ 119
20.6.2 Setting the Parameter view (ParameterView) parameter.... 119
20.6.3 Setting the Input configuration (Input Config) parameter . 120
To Next Page
Loading...
Need help?
General
