Eaton EDR 3000 - Page 472

To Next Page

To Previous Page

EDR-3000 IM02602003E

Device Planning Parameters of the Zone Interlocking

Parameter Description Options Default Menu path

Mode Mode Use Use [Device Planning]

www.eaton.com 460

Main Page

EDR-3000 Functional Overview14
Table of Contents15
Comments on the Manual20
What Is Included with the Device25
Storage25
Important Information25
Symbols26
General Conventions32
Load Reference Arrow System33
Device34
Device Planning34
Device Planning Parameters of the Device35
Installation and Wiring36
Three-Side-View and Panel Cutout36
Overview of Slots - Assembly Groups39
Slot X1: Power Supply Card with Digital Inputs41
Slot X2: Relay Output Card, IRIG-B, Zone Interlock, SC46
Slot X3: Current Transformer Measuring Inputs53
Slot X100: Ethernet Interface63
Slot X101: IRIG-B00X65
Slot X103: Data Communication67
Slot X120 - PC Interface72
Control Wiring Diagram73
Input, Output and LED Settings75
Digital Input Configuration75
DI-8P X76
DI-4P X Settings80
Wired Inputs (Aliases)83
Relay Output Configuration87
RO-3 X Settings90
RO-5 X Settings103
RO-3ZI X - Settings123
LED Configuration137
The »System OK (Operational) « LED140
LED Settings141
Front Panel158
Basic Menu Control163
Powerport-E Keyboard Commands164
Powerport-E165
Installation of Powerport-E166
Uninstalling Powerport-E166
Setting up the Connection PC - Device167
Loading of Device Data When Using Powerport-E178
Restoring Device Data When Using Powerport-E178
Backup and Documentation When Using Powerport-E179
Printing of Device Data When Using Powerport-E (Setting List)179
Off-Line Device Planning Via Powerport-E181
Powerport-E Keyboard Commands182
Measuring Values183
Read out Measured Values183
Current - Measured Values186
Statistics189
Configuration of the Minimum and Maximum Values189
Configuration of the Average Value Calculation190
Direct Commands192
Global Protection Parameters of the Statistics Module192
States of the Inputs of the Statistics Module194
Signals of the Statistics Module195
Counters of the Module Statistics195
System Alarms199
Demand Management199
Peak Demand202
Min. and Max. Values202
THD Protection202
Device Planning Parameters of the Demand Management203
Signals of the Demand Management (States of the Outputs)203
Global Protection Parameter of the Demand Management203
States of the Inputs of the Demand Management205
Resets206
Manual Acknowledgment208
Manual Acknowledgment Via Powerport-E208
External Acknowledgments209
External Acknowledge Via Powerport-E209
External LED - Acknowledgment Signals210
Manual Resets220
Manual Resets Via Powerport-E220
Reset to Factory Defaults220
Status Display221
Status Display Via Powerport E221
Operating Panel (HMI)222
Special Parameters of the Panel222
Direct Commands of the Panel222
Global Protection Parameters of the Panel222
Recorders223
Waveform Recorder223
Fault Recorder234
Event Recorder242
Trend Recorder246
Time Synchronization251
Accuracy of Time Synchronization252
Sntp259
Irig-B00X267
Device Parameters272
Date and Time272
Version272
Version Via Powerport-E272
TCP/IP Settings273
Direct Commands of the System Module274
Global Protection Parameters of the System275
System Module Input States277
Special Values of the System Module279
Communication Protocols280
Modbus280
Iec 61850287
Parameters302
Parameter Definitions302
Access Authorizations (Access Areas)317
Passwords - Areas317
How to Find out What Access Areas/Levels Are Unlocked321
Unlocking Access Areas321
Changing Passwords322
Adaptive Parameters Via HMI323
Access Authorizations (Access Areas)326
Passwords - Areas326
How to Find out What Access Areas/Levels Are Unlocked330
Unlocking Access Areas331
Changing Passwords331
Changing Passwords Via Power-Port-E332
Password Entry at the Panel332
Password Forgotten332
Parameter Setting at the HMI333
Parameter Setting Via Power-Port-E337
Setting Groups340
Comparing Parameter Files Via Powerport-E353
Converting Parameter Files Via Powerport-E354
Program Mode355
System Parameters356
General System Parameters356
System Parameters - Current Related357
Blocking358
Permanent Blocking358
Temporary Blocking358
To Activate or Deactivate the Tripping Command of a Protection Module360
Activate, Deactivate Respectively to Block Temporary Protection Functions361
Protection (Prot) Module363
How to Block All Protective and Supervisory Functions363
Direct Commands of the Protection Module370
Global Protection Parameters of the Protection Module370
Protection Module Input States371
Protection Module Signals (Output States)371
Values of the Protection Module372
Switchgear/Breaker - Manager373
Breaker Configuration373
Single Line Diagram375
Switching the Breaker at the Panel394
Breaker Wear396
Control - Example: Switching of a Breaker413
Protective Elements416
50P - DEFT Overcurrent Protection416
51P - INV Overcurrent-Protection425
50X DEFT Measured Ground Fault Protection434
51X INV Measured Ground Fault Protection443
50R DEFT Calculated Ground Fault Protection Module452
51R INV Calculated Ground Fault Protection461
ZI - Zone Interlocking470
46 - Current Unbalance Protection488
CLPU - Supervision Module Cold Load Pickup496
SOTF - Switch Onto Fault Protection505
79 - Automatic Reclosure513
Exp - External Protection550
Supervision556
BF- Breaker Failure [50BF*/62BF]556
CTS - Current Transformer Supervision581
74TC - Trip Circuit Monitoring588
Self Supervision596
Programmable Logic599
General Description599
Programmable Logic at the Panel605
Programmable Logic Via Powerport-E605
Commissioning627
Commissioning/Protection Test628
Decommissioning - Removing the Plug from the Relay629
Service and Commissioning Support630
Maintenance Mode631
Principle - General Use631
Before Use632
How to Use the Maintenance Mode632
Forcing the Relay Output Contacts634
Disarming the Relay Output Contacts635
Forcing Rtds637
Forcing Analog Outputs638
Forcing Analog Inputs639
Failure Simulator (Sequencer)640
Technical Data653
Climatic Environmental Conditions653
Degree of Protection en 60529653
Routine Test653
Housing654
Current and Ground Current Measurement655
Voltage Supply657
Power Consumption657
Display658
Front Interface RS232658
Real Time Clock659
Digital Inputs660
Relay Outputs661
Time Synchronization IRIG-B00X662
Zone Interlocking663
Rs485664
Fiber Optic664
URTD-Interface664
Boot Phase665
Standards666
Approvals666
Design Standards666
High Voltage Tests (IEC 60255-1)666
EMC Immunity Tests667
EMC Emission Tests668
Environmental Tests669
Environmental Tests670
Mechanical Tests671
Specifications672
Specifications of the Real Time Clock672
Time Synchronization Tolerances672
Specifications of the Measured Value Acquisition673
Protection Elements Accuracy674
Appendix677
Instantaneous Current Curves (Phase)687
Time Current Curves (PHASE)688
Instantaneous Current Curves (Ground Current Calculated)700
Instantaneous Current Curves (Ground Current Measured)702
Time Current Curves (Ground Current)704
Assignment List716
List of ANSI Codes768

Eaton EDR 3000 - Page 472

Table of Contents

Related product manuals