EPRAD eCNA-10 - Program and Macro Instruction Details

© EPRAD Incorporated
Program and Macro Instructions (continued)
Program and Macro Instructions
Instruction Parameters / Offset Time
RemDev1: m1 m2 m3 dd:dd m1 = Remote Device 1 Name m2 = Message Name m3 = Tmr1 to Tmr15
dd:dd = 0:00 to 99:99 minutes:seconds
RemDev2: m1 m2 m3 dd:dd m1 = Remote Device 2 Name m2 = Message Name m3 = Tmr1 to Tmr15
dd:dd = 0:00 to 99:99 minutes:seconds
RemDev3: m1 m2 m3 dd:dd m1 = Remote Device 3 Name m2 = Message Name m3 = Tmr1 to Tmr15
dd:dd = 0:00 to 99:99 minutes:seconds
RemDev4: m1 m2 m3 dd:dd m1 = Remote Device 4 Name m2 = Message Name m3 = Tmr1 to Tmr15
dd:dd = 0:00 to 99:99 minutes:seconds
RemDev5: m1 m2 m3 dd:dd m1 = Remote Device 5 Name m2 = Message Name m3 = Tmr1 to Tmr15
dd:dd = 0:00 to 99:99 minutes:seconds
RemDev6: m1 m2 m3 dd:dd m1 = Remote Device 6 Name m2 = Message Name m3 = Tmr1 to Tmr15
dd:dd = 0:00 to 99:99 minutes:seconds
RemDev7: m1 m2 m3 dd:dd m1 = Remote Device 7 Name m2 = Message Name m3 = Tmr1 to Tmr15
dd:dd = 0:00 to 99:99 minutes:seconds
RemDev8: m1 m2 m3 dd:dd m1 = Remote Device 8 Name m2 = Message Name m3 = Tmr1 to Tmr15
dd:dd = 0:00 to 99:99 minutes:seconds
RemDev9: m1 m2 m3 dd:dd m1 = Remote Device 9 Name m2 = Message Name m3 = Tmr1 to Tmr15
dd:dd = 0:00 to 99:99 minutes:seconds
RemDev10: m1 m2 m3 dd:dd m1 = Remote Device 10 Name m2 = Message Name m3 = Tmr1 to Tmr15
dd:dd = 0:00 to 99:99 minutes:seconds
Show Status: m1 m2 dd:dd m1 = Auto; Ready to Run; Ready to Resume; Running; Intermission
m = Tmr1 to Tmr15
dd:dd = 0:00 to 99:99 minutes:seconds
Alarm: m1 m2 dd:dd m1 = On, Off, Toggle
m2 = Tmr1 to Tmr15
dd:dd = 0:00 to 99:99 minutes:seconds
Light Level: m1 m2 m3 m4 dd:dd m1 = Zone: House, Stage, Zone 3 to Zone 16
m2 = Preset: Up, Down, Mid1, Mid2, None, No-op
m3 = Light Level Offset %: -100% to +100%
m4 = Fade-in Time: “ ”, 0 Sec to 99 Sec
dd:dd = 0:00 to 99:99 minutes:seconds
Wake-On-LAN: m1 m2 dd:dd m1 = Device Name
m2 = Tmr1 to Tmr15
dd:dd = 0:00 to 99:99 minutes:seconds
** Control Event: m1 m2 dd:dd m1 = Start; Resume; Stop; Fault Set; Fault Clear; Cue; Abort; Set Program 1 - 9; Reboot eCNA
m2 = Tmr1 to Tmr15
dd:dd = 0:00 to 99:99 minutes:seconds
** If(time): m1 m2 m3 m1 = Of Show (Run Time); Between Shows; Before Start; After Start; Before End; After End
m2 = < ; <= ; > ; >=
m3 = Then Exit; Then Goto 1 through 16
d = decimal number
m = message
* Not available in the Macro Editor
** Not available in the Program Editor
60
eCNA-10 Operation and Installation Manual Version 1.270-00