Need help?Do you have a question about the Fujitsu FLASHWAVE 7500 and is the answer not in the manual?
General| Category | Optical Transport Network |
|---|---|
| Application | Metro and regional optical transport |
| Technology | Optical Transport Network (OTN) |
| Capacity per Port | 10 Gbps, 40 Gbps, 100 Gbps |
| Channel Spacing | 50 GHz, 100 GHz |
| Client Interfaces | Ethernet, SONET/SDH, Fibre Channel, OTU2/OTU3/OTU4 |
| Protocols Supported | OTN |
| Power Supply | -48 VDC, AC options available |
| Operating Temperature | 0°C to 40°C |
| Relative Humidity | 5% to 85% non-condensing |
| Weight | Varies by configuration |
| Form Factor | Chassis-based system |
| Supported Distances | Long-haul (thousands of kilometers), Metro (hundreds of kilometers) |
Provides installation procedures for the FLASHWAVE 7500 Core Configuration system.
Lists requirements for Core Configuration equipment and tools.
Describes variations in rack configurations for system racks.
Details how to store, unpack, and inspect FLASHWAVE 7500 equipment.
Provides steps for installing a standard rack.
Details the procedure for installing the circuit breaker panel.
Explains how to connect the office battery to the CBP power input.
Instructions for installing shelves and heat baffles into a relay rack.
Provides instructions for installing cooling fans and DCM shelves.
Details installing power, ground, and alarm cabling for standard rack configurations.
Verifies power connections to the Optical/Tributary shelf.
Checks ground resistance at the shelf power input.
Covers connections made to the Optical/Tributary shelf backplane.
Provides installation procedures for the FLASHWAVE 7500 Small Configuration system.
Lists requirements for Small Configuration equipment and tools.
Describes rack configurations and shelf flange kits for mounting shelves.
Details how to store, unpack, and inspect FLASHWAVE 7500 equipment.
Provides steps for installing a standard rack.
Details installing the circuit breaker or fuse panel.
Explains connecting the office battery to the CBP and checking voltage.
Instructions for installing Optical/Tributary shelves into relay racks.
Instructions for installing a 23-inch heat baffle.
Instructions for installing a 19-inch heat baffle.
Instructions for installing a 23-inch DCM shelf.
Instructions for installing a 19-inch DCM shelf.
Instructions for installing the LAS2 shelf.
Instructions for installing the LAM/DCM shelf (SDL1).
Installation instructions for cooling fans.
Details installing power, ground, and alarm cabling.
Verifies power connections to the Optical/Tributary shelf.
Checks ground resistance at the shelf power input.
Covers connections made to the Extension shelf backplane.
Provides installation procedures for the FLASHWAVE 7500 ETSI Configuration system.
Lists requirements for ETSI Configuration equipment and tools.
Describes rack configurations and shelf flange kits for ETSI racks.
Details how to store, unpack, and inspect FLASHWAVE 7500 equipment.
Provides steps for installing a standard rack.
Details installing the ETSI power distribution panel.
Explains connecting office battery to PDP and checking voltage.
Instructions for installing Optical/Tributary shelves into ETSI racks.
Instructions for installing an ETSI heat baffle.
Instructions for installing an ETSI DCM shelf.
Instructions for installing the ETSI LAM/DCM shelf (SDL1).
Instructions for installing fans, rack covers, and end panels.
Details installing power and ground cabling for ETSI rack configurations.
Verifies power connections to the Optical/Tributary shelf.
Checks ground resistance at the shelf power input.
Covers connections made to the Optical/Tributary shelf SIA.
Provides installation procedures for the FLASHWAVE 7500 Extension Configuration system.
Lists requirements for Extension Configuration equipment and tools.
Describes rack configurations for system racks.
Details how to store, unpack, and inspect FLASHWAVE 7500 equipment.
Provides steps for installing a standard rack.
Details the procedure for installing the circuit breaker panel.
Explains connecting office battery to CBP and checking voltage.
Instructions for installing Extension shelves and heat baffles.
Provides instructions for installing fans and DCM shelves.
Details installing power, ground, and alarm cabling.
Verifies power connections to the Extension shelf.
Checks ground resistance at the shelf power input.
Covers connections made to the Extension shelf backplane.
Overview of procedures for installing/removing units used in configuration systems.
Lists considerations for installing/removing modules and plug-in units.
Procedures for removing and installing plug-in units into shelf slots.
Instructions for removing and installing filler panels.
Procedures for removing and installing SFP modules.
Procedures for removing and installing XFP modules.
To Next Page
