[SwitchE] interface xgigabitethernet 0/0/2
[SwitchE-XGigabitEthernet0/0/2] stp disable
[SwitchE-XGigabitEthernet0/0/2] quit
# Disable STP on the interfaces to be added to the RRPP ring on Switch D.
[SwitchD] interface xgigabitethernet 0/0/1
[SwitchD-XGigabitEthernet0/0/1] stp disable
[SwitchD-XGigabitEthernet0/0/1] quit
[SwitchD] interface xgigabitethernet 0/0/2
[SwitchD-XGigabitEthernet0/0/2] stp disable
[SwitchD-XGigabitEthernet0/0/2] quit
Step 5 Create RRPP rings.
Configure nodes on ring 2. The configuration procedure is as follows:
# Configure Switch A as the master node of ring 2 and specify the primary and secondary
interfaces.
[SwitchA] rrpp domain 2
[SwitchA-rrpp-domain-region2] ring 2 node-mode master primary-port
xgigabitethernet 0/0/1 secondary-port xgigabitethernet 0/0/2 level 0
[SwitchA-rrpp-domain-region2] ring 2 enable
[SwitchA-rrpp-domain-region2] quit
# Configure SwitchB as a transit node of ring 2 (major ring) and specify the primary and
secondary interfaces.
[SwitchB] rrpp domain 2
[SwitchB-rrpp-domain-region2] ring 2 node-mode transit primary-port
xgigabitethernet 0/0/1 secondary-port xgigabitethernet 0/0/2 level 0
[SwitchB-rrpp-domain-region2] ring 2 enable
[SwitchB-rrpp-domain-region2] quit
# Configure Switch C as a transit node of RRPP ring 2 and specify the primary and secondary
interfaces.
[SwitchC] rrpp domain 2
[SwitchC-rrpp-domain-region2] ring 2 node-mode transit primary-port
xgigabitethernet 0/0/3 secondary-port xgigabitethernet 0/0/4 level 0
[SwitchC-rrpp-domain-region2] ring 2 enable
[SwitchC-rrpp-domain-region2] quit
Configure nodes on ring 1. The configuration procedure is as follows:
# Configure Switch E as the master node of ring 1 (major ring) and specify the primary and
secondary interfaces.
[SwitchE] rrpp domain 1
[SwitchE-rrpp-domain-region1] ring 1 node-mode master primary-port
xgigabitethernet 0/0/1 secondary-port xgigabitethernet 0/0/2 level 0
[SwitchE-rrpp-domain-region1] ring 1 enable
[SwitchE-rrpp-domain-region1] quit
# Configure Switch C as a transit node of ring 1 and specify the primary and secondary interfaces.
[SwitchC] rrpp domain 1
[SwitchC-rrpp-domain-region1] ring 1 node-mode transit primary-port
xgigabitethernet 0/0/1 secondary-port xgigabitethernet 0/0/2 level 0
[SwitchC-rrpp-domain-region1] ring 1 enable
[SwitchC-rrpp-domain-region1] quit
# Configure Switch D as a transit node of ring 1 and specify the primary and secondary interfaces.
[SwitchD] rrpp domain 1
[SwitchD-rrpp-domain-region1] ring 1 node-mode transit primary-port
xgigabitethernet 0/0/1 secondary-port xgigabitethernet 0/0/2 level 0
Quidway S6700 Series Ethernet Switches
Configuration Guide - Reliability 3 RRPP Configuration
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
92
To Next Page
Loading...
