# Configure the VLANs mapping instance 2 as the protected VLANs in domain 2. Configure
VLAN 10 as the control VLAN.
[UPED] rrpp domain 2
[UPED-rrpp-domain-region2] protected-vlan reference-instance 2
[UPED-rrpp-domain-region2] control-vlan 10
[UPED-rrpp-domain-region2] quit
l Configure PE-AGG.
# Configure the VLANs mapping instance 1 as the protected VLANs in domain 1. Configure
VLAN 5 as the control VLAN.
[PE-AGG] rrpp domain 1
[PE-AGG-rrpp-domain-region1] protected-vlan reference-instance 1
[PE-AGG-rrpp-domain-region1] control-vlan 5
[PE-AGG-rrpp-domain-region1] quit
# Configure the VLANs mapping instance 2 as the protected VLANs in domain 2. Configure
VLAN 10 as the control VLAN.
[PE-AGG] rrpp domain 2
[PE-AGG-rrpp-domain-region2] protected-vlan reference-instance 2
[PE-AGG-rrpp-domain-region2] control-vlan 10
[PE-AGG-rrpp-domain-region2] quit
Step 4 Create an RRPP ring.
l Configure PE-AGG.
# Configure PE-AGG as the master node of ring 1 in domain 1. Configure XGE 0/0/1 as the
primary port and XGE 0/0/2 as the secondary port.
[PE-AGG] rrpp domain 1
[PE-AGG-rrpp-domain-region1] ring 1 node-mode master primary-port
xgigabitethernet 0/0/1 secondary-port xgigabitethernet 0/0/2 level 0
[PE-AGG-rrpp-domain-region1] ring 1 enable
[PE-AGG-rrpp-domain-region1] quit
# Configure PE-AGG as the master node of ring 1 in domain 2. Configure XGE 0/0/2 as the
primary port and XGE 0/0/1 as the secondary port.
[PE-AGG] rrpp domain 2
[PE-AGG-rrpp-domain-region2] ring 1 node-mode master primary-port
xgigabitethernet 0/0/2 secondary-port xgigabitethernet 0/0/1 level 0
[PE-AGG-rrpp-domain-region2] ring 1 enable
[PE-AGG-rrpp-domain-region2] quit
l Configure UPE A.
# Configure UPE A as a transit node of ring 1 in domain 1 and specify primary and secondary
ports on UPE A.
[UPEA] rrpp domain 1
[UPEA-rrpp-domain-region1] ring 1 node-mode transit primary-port
xgigabitethernet 0/0/1 secondary-port xgigabitethernet 0/0/2 level 0
[UPEA-rrpp-domain-region1] ring 1 enable
[UPEA-rrpp-domain-region1] quit
# Configure UPE A as a transit node of ring 1 in domain 2 and specify primary and secondary
ports on UPE A.
[UPEA] rrpp domain 2
[UPEA-rrpp-domain-region2] ring 1 node-mode transit primary-port
xgigabitethernet 0/0/1 secondary-port xgigabitethernet 0/0/2 level 0
[UPEA-rrpp-domain-region2] ring 1 enable
[UPEA-rrpp-domain-region2] quit
l Configure UPE D.
# Configure UPE D as a transit node of ring 1 in domain 1 and specify primary and secondary
ports on UPE D.
[UPED] rrpp domain 1
[UPED-rrpp-domain-region1] ring 1 node-mode transit primary-port
Quidway S6700 Series Ethernet Switches
Configuration Guide - Reliability 3 RRPP Configuration
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
118
To Next Page
Loading...
