xgigabitethernet 0/0/1 secondary-port xgigabitethernet 0/0/2 level 0
[UPED-rrpp-domain-region1] ring 1 enable
[UPED-rrpp-domain-region1] quit
# Configure UPE D as a transit node of ring 1 in domain 2 and specify primary and secondary
ports on UPE D.
[UPED] rrpp domain 2
[UPED-rrpp-domain-region2] ring 1 node-mode transit primary-port
xgigabitethernet 0/0/1 secondary-port xgigabitethernet 0/0/2 level 0
[UPED-rrpp-domain-region2] ring 1 enable
[UPED-rrpp-domain-region2] quit
l # Configure UPE B.
# Configure UPE B as a transit node of ring 1 in domain 1 and specify primary and secondary
ports on UPE B.
[UPEB] rrpp domain 1
[UPEB-rrpp-domain-region1] ring 1 node-mode transit primary-port
xgigabitethernet 0/0/1 secondary-port gxgigabitethernet 0/0/2 level 0
[UPEB-rrpp-domain-region1] ring 1 enable
[UPEB-rrpp-domain-region1] quit
# Configure UPE B as a transit node of ring 1 in domain 2 and specify primary and secondary
ports on UPE B.
[UPEB] rrpp domain 2
[UPEB-rrpp-domain-region2] ring 1 node-mode transit primary-port
xgigabitethernet 0/0/1 secondary-port xgigabitethernet 0/0/2 level 0
[UPEB-rrpp-domain-region2] ring 1 enable
[UPEB-rrpp-domain-region2] quit
# Configure UPE B as an edge node of ring 2 in domain 1. Configure XGE 0/0/1 as the public
port and XGE 0/0/3 as the edge port.
[UPEB] rrpp domain 1
[UPEB-rrpp-domain-region1] ring 2 node-mode edge common-port xgigabitethernet
0/0/1 edge-port xgigabitethernet 0/0/3
[UPEB-rrpp-domain-region1] ring 2 enable
[UPEB-rrpp-domain-region1] quit
# Configure UPE B as an edge node of ring 2 in domain 2. Configure XGE 0/0/1 as the public
port and XGE 0/0/3 as the edge port.
[UPEB] rrpp domain 2
[UPEB-rrpp-domain-region2] ring 2 node-mode edge common-port xgigabitethernet
0/0/1 edge-port xgigabitethernet 0/0/3
[UPEB-rrpp-domain-region2] ring 2 enable
[UPEB-rrpp-domain-region2] quit
# Configure UPE B as an edge node of ring 3 in domain 1. Configure XGE 0/0/1 as the public
port and XGE 0/0/4 as the edge port.
[UPEB] rrpp domain 1
[UPEB-rrpp-domain-region1] ring 3 node-mode edge common-port xgigabitethernet
0/0/1 edge-port xgigabitethernet 0/0/4
[UPEB-rrpp-domain-region1] ring 3 enable
[UPEB-rrpp-domain-region1] quit
# Configure UPE B as an edge node of ring 3 in domain 2. Configure XGE 0/0/1 as the public
port and XGE 0/0/4 as the edge port.
[UPEB] rrpp domain 2
[UPEB-rrpp-domain-region2] ring 3 node-mode edge common-port xgigabitethernet
0/0/1 edge-port xgigabitethernet 0/0/4
[UPEB-rrpp-domain-region2] ring 3 enable
[UPEB-rrpp-domain-region2] quit
l Configure UPE C.
# Configure UPE C as a transit node of ring 1 in domain 1 and specify primary and secondary
ports on UPE C.
[UPEC] rrpp domain 1
[UPEC-rrpp-domain-region1] ring 1 node-mode transit primary-port
Quidway S6700 Series Ethernet Switches
Configuration Guide - Reliability 3 RRPP Configuration
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
119
To Next Page
Loading...
