IEMCA KID 80 - Page 11

126 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

1 - BASE INFORMATION KID 80 SIV

EN

1 - Pag. 5 / 15

Table of Contents

Table of Contents5
Index5
Base Information9
Control Description9
- Main Switch10
- Emergency Stop Push-Button10
Keyboard Control Description12
Main Screens: Description16
Working Screen16
Setup Screen17
- Evt (Events) Function18
- Psw (Password) Function18
- Tim (Time) Function18
- Sys (System) Function20
- Ext (Exit) Function20
Piece Counter Reset Mode21
Information for Use23
Automatic Cycle Start24
0-Axis Procedure (Manual Mode)26
Cycle Performing Mode in the Step-By-Step Function27
- Bar Loading Cycle - Facing Procedure29
- Bar Feeder Stop in Emergency30
Bar Feeder Stop30
Operator Parameters: Operation Mode31
Parameter Accessing and Display32
Access to and Display of Common Parameters32
How to Access and Display Iemca Parameters34
Parameter Modification36
Subparameters Display37
Subparameter Modification38
Exiting the Parameters39
Operator Parameters: Description39
- Bar End Adjustment40
- Additional Bush Opening at a Fixed Value42
- Facing Length43
- Facing Mode43
- Short Feeding Safety44
- Long Feeding Safety45
- Piece Length46
- Open Collet Thrust Delay47
- Closed Collet Thrust Delay47
- Collet Entry Slowdown48
- Collet Entry Speed49
- Collet Entry Torque50
- Pulse Number51
- Pulse Stroke53
- Spindle Pulses - On-Time53
- Spindle Pulses - Off-Time54
- Cycle Start Delay54
- Remnant Handling55
- Bar Change Advance no First Feeding57
- Description of the Phase Order57
- Bar Change Advance no Facing58
- Open Collet Timeout58
- Piece Timeout59
- Bar Feeding Handling59
- Pieces before the Lathe Stop60
- Start Machining60
- Minutes before the Lathe Stop61
- Closed Collet Speed61
- Max. Feeding Pos. Adjustment62
- K1 Immediate Exit64
- K2 Inversion64
- Feeding Torque65
- Fixed-Piece Feeding66
- K15 Disabling66
- K15 Duration67
- K13 Duration67
- Spindle Stop68
- Bar Pusher Return at Collet Closing69
- First Feeding Value71
- Bar Pusher Return Pause71
- Parameter "Speed Change in First Feeding" 1 = Fast73
- Parameter "Speed Change in First Feeding" 0 = Slow73
- Axis Operation74
- Bar Pusher Stop with Closed Collet74
- Axis Stop Engagement Delay74
- Closed Collet Torque74
Errors - Causes - Solutions76
- Error: the Bar Fails to Enter into the Collet77
- Error: Gate Open77
- Error: Short Feeding78
- Error: Bar too Long79
- Long Feed79
- Preset Qty. Reached, Reset - P2680
- Bar Feeder Emergency80
- Wrong Facing Position81
- Stationary Position before Pulses81
- Axial Displacement Not Locked83
- Motor Thermal Circuit Breakers83
- Failure During the Bar Change84
- No Bar84
- Machine Ok84
- Thread Safety85
- Carry out the 0-Axis after a Power Off-On85
- Explanation of Messages86
2.12.1 Operator Panel Message List86
With the Bar Feeder in Manual Mode87
2.12.2 Conditions that May Cause a Generic Alarm on the Lathe87
Program Identification Data: Display Mode88
Protected Parameters: Display90
How to Access and Display the Protected Parameters91
How to Access and Display Parameters93
Subparameters Display95
How to Exit the Protected Parameters95
Protected Parameters: Description95
Parameters for Reference Values: Description96
- Bar Feeder Zero Setting96
- Lubrication Stop Value101
- Operating Cycle - Description102
- Maximum Bar Length104
Parameters for Reference Values: Description104
Axis Function Parameters: Description106
- Torque Reduction in Manual Mode109
- Toque Reduction During Bar Change110
- Keyboard on the Opposite Side111
- Torque Reduction in Automatic Mode111
- Interface Signals112
Interface Parameters: Description112
- Fair Demo113
- Wrong Bar Feeder Phase113
General Parameters: Description113
- Attachments115
- Example of Filling in116
Assistance Request116
- Hardware and Program Identification Data117
- Parameter List for the Operator118
- Operator Parameter List118
Dparameter List for the Reference Values122
Eparameter List for the Axis Functions123
- Parameter List for the Interface125
- General Parameter List126

Other manuals for IEMCA KID 80

Manual For Use And Maintenance82 pages

Related product manuals

Preview: IEMCA Master 80 UP HyperFlexible

IEMCA Master 80 UP HyperFlexible

Preview: IEMCA BOSS 332

Preview: IEMCA BOSS 338 HD

IEMCA BOSS 338 HD

IEMCA BOSS 542 CNC

IEMCA BOSS 552 - IC

IEMCA MASTER 880 MP-E

Preview: IEMCA Elite Evo Series

IEMCA Elite Evo Series

Preview: IEMCA MASTER 880-VERSO P

IEMCA MASTER 880-VERSO P

IEMCA MINI BOSS 325r CNC

IEMCA BOSS 332-545-551 E