EasyManuals Logo

Juniper QFX Series Hardware Guide

Juniper QFX Series
176 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #165 background imageLoading...
Page #165 background image
que le fil de masse devrait toujours être relié d'abord et débranché pour la
dernière fois.
Warnung Die Stromzufuhrist nur mit geeigneten Ringösenan dasDC Netzteil
anzuschliessen. Die richtige Anschlusssequenz ist: Erdanschluss zu
Erdanschluss, +RTN zu +RTN und dann -48V zu -48V. Die richtige Sequenz
zum Abtrennen der Stromversorgung ist -48V zu -48V, +RTN zu +RTN und
dann Erdanschlusszu Erdanschluss. Es ist zu beachten dass der Erdanschluss
immer zuerst angeschlossen und als letztes abgetrennt wird.
Avvertenza Mostra lamorsettiera dell alimentatore CC.Cablare l'alimentatore
CC usando i connettori adatti all'estremità del cablaggio, come illustrato. La
corretta sequenza di cablaggio è da massa a massa, da positivo a positivo
(da linea ad L) e da negativo a negativo (da neutro a N). Tenere presente che
il filo di massa deve semprevenire collegato per primo e scollegato per ultimo.
Advarsel Riktig tilkoples tilkoplingssekvens er jord til jord, +RTN til +RTN,
–48 V til – 48 V. Riktig frakoples tilkoplingssekvens er –48 V til – 48 V, +RTN
til +RTN, jord til jord.
Aviso Ate con alambre la fuente de potencia cc Usando los terminales
apropiados en el extremo del cableado. Al conectar potencia, la secuencia
apropiada del cableado se muele para moler, +RTN a +RTN, entonces –48 V
a –48 V. Al desconectar potencia, la secuencia apropiada del cableado es
–48 V a –48 V, +RTN a +RTN, entonces molió para moler. Observe que el
alambre de tierra se debe conectar siempre primero y desconectar por último.
Observe que el alambre de tierra se debe conectar siempre primero y
desconectar por último.
¡Atención! Wire a fonte de alimentação de DC Usando os talões apropriados
na extremidade da fiação. Ao conectar a potência, a seqüência apropriada
da fiação é moída para moer, +RTN a +RTN, então –48 V a –48 V. Ao
desconectar a potência, a seqüência apropriada da fiação é –48 V a –48 V,
+RTN a +RTN, moeu então para moer. Anote que o fio à terra deve sempre
ser conectado primeiramente e desconectado por último. Anote que o fio à
terra deve sempre ser conectado primeiramente e desconectado por último.
Varning! Korrekt kopplingssekvens ar jord till jord, +RTN till +RTN, –48 V till
–48 V. Korrekt kopplas kopplingssekvens ar –48 V till –48 V, +RTN till +RTN,
jord till jord.
DC Power Wiring Terminations Warning
WARNING: When stranded wiring is required, use approved wiring
terminations, such as closed-loop or spade-type with upturned lugs. These
terminations must be the appropriate size for the wires and must clamp both
the insulation and conductor.
165Copyright © 2019, Juniper Networks, Inc.
Chapter 7: Safety and Compliance Information

Table of Contents

Other manuals for Juniper QFX Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Juniper QFX Series and is the answer not in the manual?

Juniper QFX Series Specifications

General IconGeneral
CategorySwitch
SeriesQFX
Form Factor1U, 2U, and modular chassis options
Power SupplyRedundant, hot-swappable power supplies
Coolinghot-swappable fans
Virtual ChassisSupported on certain models
Typical UseData center, cloud
Operating SystemJunos OS
ManagementCLI
Key FeaturesHigh performance, low latency, automation
LatencySub-microsecond latency
Port DensityVaries by model (e.g., QFX5100: up to 48x10GbE + 6x40GbE)

Related product manuals