Korg microSTATION - Master Effects

Using Effects
48
Double-size effects
Double‐sizeeffects(D00:St.MltLmt–D13:EarlyRef)
usetwiceasmuchprocessingareaasothereffects.
D00:St.MltLmt–D10:RotaryODcanbeusedwith
inserteffect1,D00:St.MltLmt–D09:Vocodercanbe
usedwithinserteffects2–4,andD00:St.MltLmt–D13:
EarlyRefcanbeusedwithmastereffect1.
Whenyouuseadouble‐sizeeffect,thenext‐numbered
effectwillbeunavailable.Forexampleifyou’ve
selectedadouble‐sizeeffectforIFX1,youwon’tbe able
touseIFX2.Ifyou’veselectedadouble‐sizeeffectfor
MFX1,youwon’ tbeabletouseMFX2.
Master effects
1. “Send1”and“Send2”settings(steps3or9)
determinetheinputleveltothemastereffects.If
“Send1”and“Send2”aresetto0,nothingwillbe
inputtothemastereffects.“Send1”corresponds
toMFX1,and“Send2”correspondstoMFX2.
Let’sadjustsettingsformastereffect1.
2. AccessPROGEDIT:MFX1,andpressthe
button.
ThefirstpageofMFX1isthemastereffect1
selectionscreen(“MFX1Select”).
Pressthebuttononceagain,andthenusethe
buttonstoselecttheeffecttypeformaster
effect1.
Theprocedureisthesameasfortheinserteffects
(step5).
Note: Double‐si
zeeffectscanbeselectedonlyfor
MFX1(p. 48“Double‐sizeeffects”).
Ifyoupressthebuttontoenterthepageatright,
you’llseetheparametersfortheselectedmaster
effect(step5).
3. Specifythemastereffect1on/offsettingand
returnlevel.
Use“On/Off”toturnonmastereffect1.
IfitisOff,theoutputofthemastereffectwillbe
mu
ted.
Use“Return1”toadjusttheoutputlevelofmaster
effect1.
Note: Foreacheffect’s“Wet/Dry”setting,theWet
valueistheoutputlevelofthateffect.Thisvalueis
multipliedbythereturnset
ting(with“Return”=
127asx1.0
)todeterminetheactualoutputlevelof
themastereffect.
Note: Theoutputlevelofmastereffect2isadjusted
byPROGEDIT:MFX2“Return2.”
4. Turn“Chain”On.
When“Chain”isOn,mastereffects1and2willbe
series‐connectedintheorderofMFX1MFX2.
Youcannotchangetheorderofconnection.
Theorde
risfixedasMFX1MFX2.
“ChainLevel”specifiesthelevelfrommastereffect
1tomastereffect2.
5. UsethepageslocatedattherightofPROGEDIT:
MFX1“MFX1Select”toedittheparametersof
mastereffect1.
Fordetailsontheparametersofeacheffect,please
refertoPGp.
219andfollowing.
Total effect
1. Thesignalwillbeinputtothetotaleffectifyou
use“Bus”tosettheoscillatoroutputtoL/R,orif
yousetthe“Bus”followingtheinserteffecttoL/
R.
Theoutputfromeachmastereffectisinputtothe
totaleffectviathePROGEDIT:MFX1and2
“Return1”and“Return2”settings.
Afte
rpassingthroughthetotaleffect,thesignalis
outputfromOUTPUTL/MONOandR.
2. AccessPROGEDIT:TFX,andpressthebutton.
ThefirstpageofTFXisthetotaleffectselection
screen(“TFXSelect”).
Pressthebuttononceagain,andthenusethe
buttonstoselectaneffecttypeforthetotal
effect.
Youcan’
tusedouble‐sizeeffectswiththetotaleffect
(p. 48“Double‐sizeeffects”).
Ifyoupressthebuttontoenterthepageatright,
you’llseetheparametersfortheselectedtotaleffect
(step4).
3. UseOn/OfftoturnthetotaleffectOn.
IfitisOff,theresultwillbethesameasif000:No
Effectissele
cted;theinputsignalwillbeoutput
withoutchange.