Korg microSTATION - Programs and Combinations; Songs

Troubleshooting Programs and Combinations
65
discontinuitiesinthedelaysound,andisnota
malfunction.
 Someeffects,suchasS19:St.Record,generatenoise
intentionally.Itisalsopossibletomakearesonant
filteroscillate.Pleasecheckthesettings.
 Notethatifyouusethefollowingeffectswiththe
routingdescribedbelow,afeedbackloopwillbe
cr
eated,possiblyproducingaloudnoise.Pleaseuse
caution.
Ifthesignalfromanoscillatorortimbre/track
output,orthesignalafteraninserteffect,issentto
theFXControlbusandthatsignalisoutput
directly,withthisoutputsenttotheFXControlbus,
aloudnoisemaybeoutput.(Itisalsopossiblethat
aDCcomponentwillbeoutputatth
emaximum
level,producin
gsilence.)
•WhenusingS03:St.LimitrorS06:St.Gate,andthe
“EnvSel”oftheseeffectsissetaseitherFXCtl1or
FXCtl2,and“TriggerMonitor”isOn(editableonly
byusingmicroSTATIONEditor/Plug‐InEditor).
•W
henusingD09:Vocoder,andthe“ModSrc”ofthis
effectissetaseitherFXCtl1orFXCtl2,and
“ModulatorHighMix”issettootherthan0
(editableonlybyusingmicroSTATIONEditor/
Plug‐InEditor).
Can’t play chords
 Couldtheprogram’sVo ice AssignModebesetto
Mono?PGp. 3
Pitch is incorrect
 IntheGlobal/Media:Basic,aretheMTuneand
Transposesettingscorrect?PGp. 57
 IntheProgEdit:OSC1orOSC2,isthePitchSlope
setto+1.0?PGp. 7
 Inthecombinationorsong,aretheTransposeand
Detunesettingsofeachtimbre/trackset
appropriately?PGp. 20,PGp. 39
Programs and Combinations
Settings for oscillator 2 are not displayed
 Haveyouselectedaprogramthatusesoscillator2?
Program does not sound
 Couldtheoscillatororamplevelbelowered?
PGp. 7
 Istheoscillator’s“Play/Mute”parametersetto
Play?
p. 17
A combination does not play correctly after
you load data
 Arethecategoryandindexnumberoftheprograms
usedbythecombinationthesameaswhenyou
createdthecombination?
Can’t write a Program
 IstheMemoryProtectProgramorCombioff
(GLOBAL/MEDIA:Basic)?p. 55,PGp. 60
Songs
The sound of the program selected for a
track is different than when played in
Program mode
 WhenyouselectaprogramforatrackinSequencer
mode,thearpeggiatorandeffectsettingsof
Programmodearenotassignedautomatically.
 YoucanusetheSEQEDITcommand“CopyARP,”
“CopyIFX,”or“CopyMFX/TFX”etc.tocopythe
Programmodesettings.PGp. 48
Song does not play correctly after being
loaded
 Aretheprogramsusedbythesongthesameas
whenthesongwascreated?
 Whensavingthesong,itisbesttouseSaveAllso
thattheprogramsaresavedtogetherwiththesong.
Thenwhenloading,loadboththe.PCGandthe
.SEQdata.PGp. 69
Playback does not start when you press the
Start/Stop button in Sequencer mode
 IstheClock(Global/Media:MIDI–MIDIClock)set
toInternalorAuto?PGp. 62
Can’t record in Sequencer mode
 DidyouselecttheMIDItrackthatyouwantto
record?
 IstheMemoryProtectSongoff(Global/Media:
Basic)?p. 55,PGp. 60
 IstheClock(Global/Media:MIDI–MIDIClock)set
toInternalorAuto?PGp. 62
 Whenusinglooprecording,couldyoubein
Rehearsalmode?
 TurnoffRehearsalmode.p.
36
After using the song command “Copy
Combi” to copy a combination, you can’t
record the arpeggiator as when you were
playing that combination
 WerethesettingscorrectwhenyouexecutedCopy
Combi?p. 43
 IntheCopyCombisettings,set“MultiRec?”toYes
beforeyouexecutethecopy.Thesesettingswillbe
madeautomatically.
Can’t record program changes
 IstheMIDIfilter“ProgChg”turnedOnforeach
track?ThisisOffbydefault.
 TurntheMIDIfilter“ProgChg”Onforeachtrack
beforeyourecord.
Can’t record changes in tone parameters
 Toneparametersarerecordedassystemexclusive
data.IstheGlobal/MediamodeMIDIFilter
“SysEX”turnedOn?ThisisOffbydefault.
PGp. 63