70
7.2–1: Setup
Here you can select the type of the insert effects, turn them
on/off, and make chain settings.
7.2–1a: Insert FX Setup
IFX1 On/Off — IFX5 On/Off
Insert Effect 1, 5 [000...089: name]
Insert Effect 2, 3, 4 [000...102: name]
Chain [ (Off),
(ON)]
Pan(CC#8) [L000...C064...R127]
BUS Select [L/R, 1, 2, 3, 4, 1/2, 3/4, Off]
S1 (Send1 (MFX1)) [000...127]
S2 (Send2 (MFX2)) [000...127]
These functions are the same as in Program mode. (☞PROG
7.2–1)
However, unlike in Program mode, the “Control Channel”
(7.2–1b) will be the MIDI channel that controls insert effect
dynamic modulation (Dmod) and the “Pan (CC#8),” “Send
1 (MFX1)” and “Send 2 (MFX2)” that follow the insert
effects. The control changes used are the same as in Program
mode.
If “Status” (3.1–1a/2a) is INT or BTH, incoming CC#8,
#93, or #91 will control and change the settings of the
Pan, Send 1, and Send 2 parameters that follow each
insert effect. When you change multis, tracks with a
“Status” of BTH, EXT, or EX2 will transmit and receive
these settings on the MIDI channel specified by “Con-
trol Channel” (7.2–1a).
7.2–1b: Control Channel
Control Channel [Ch01...16, All Rt.]
Select the MIDI channel that will control effect dynamic
modulation (Dmod), pan following the insert effect
“Pan (CC#8),” “Send 1 (MFX1),” and “Send 2 (MFX2).”
An asterisk “*” will be displayed at the right of the channel
number Ch01–16 for tracks that are routed to an IFX. If mul-
tiple tracks with differing MIDI channel settings are routed,
these channels specify the channel that will be used to con-
trol the effect.
All Rt. (All Routed): Control can be performed from any of
the MIDI channels of the tracks that are routed.
If “BUS Select” (7.1–1a/2a) is set to DKit for a track in
which a drum program is selected, the MIDI channel of
that track will be valid if any IFX1–5 is set to All Rt.,
regardless of the drum kit “BUS (BUS Select)” (GLO-
BAL 5.1–3a) setting or the utility setting “DrumKit IFX
Patch.”
■ 7.2–1c: UTILITY
☞ “Memory Status” (1.1–1c), “Copy Insert Effect,” “Swap
Insert Effect” (7.1–1b/2b), “Select by Category” (PROG
7.2–1b)
7.2–2: IFX1
7.2–3: IFX2
7.2–4: IFX3
7.2–5: IFX4
7.2–6: IFX5
Sets the parameters for the effects selected for IFX 1–5 in the
Setup page (
☞p.151).
■ 7.2–2(...6)a: UTILITY
☞ “Memory Status” (1.1–1c)
7.2–7: Route (Routing)
7.2–7a: Routing Map
This shows the status of the insert effects. This displays the
same contents as the 7.1: BUS, Routing page. (
☞7.1–3)
■ 7.2–7b: UTILITY
☞ “Memory Status” (1.1–1c), “Copy Insert Effect,” “Swap
Insert Effect” (7.1–1b/2b), “DKit IFX Patch” (COMBI 7.1–
1b)
MULTI 7.2: Insert FX
7.2–1a
7.2–1c7.2–1b
7.2–2a
7.2–7a
7.2–7b
To Next Page
