Korg Triton-Rack

PROG
1.1
2.12.22.33.14.14.25.15.25.36.17.17.27.3
7
2.1–2: OSC1
The multisample(s) (waveform) or drum kit on which the
program will be based can be selected here for oscillator 1
and/or oscillator 2.
Internal ROM contains 425 different multisamples (preset
multisamples) and 153 drum kits. By selecting a RAM multi-
sample, you can use a multisample that you created in Sam-
pling mode or that you loaded in Disk mode. If an EXB-
PCM series option has been installed, you will be able to
select multisamples from the installed option.
The following illustration shows a LCD screen where
“Mode (Oscillator Mode)” (2.1–1a) has been set to Double.
If this is set to Single, the OSC2 page parameter will not
appear and cannot be set.
The following illustration shows the display when “Mode
(Oscillator Mode)” (2.1–1a) has been set to Drums.
2.1–2a: OSC1 Multisample
Velocity SW L→H [001...127]
The oscillator 1 High and Low multisamples that you spec-
ify in “High, Low” (2.1–2b) will be switched at the velocity
value that you specify here. When a note with a velocity
higher than this value is received from a connected MIDI
device, the High multisample will sound.
2.1–2b: High, Low
Here you can select a multisample.
You can select different multisamples for High and Low, and
use velocity to switch between the two multisamples. Start
Offset, Reverse, and Level can be adjusted independently
for the High and Low multisamples.
High:
High MS Bank [ROM, RAM, EXB* ...]
High Multisample [000...424, 000...999]
Specifies the bank and multisample number of the High
multisample. The multisample you select here will sounded
by velocities greater than the value of the “Velocity SW
L→H” (2.1–2a) parameter. If you do not wish to use velocity
switching, set the value to 001, and select only the High mul-
tisample.
ROM: Select a preset multisample.
Use “High Multisample” to select from 000–424.
RAM: Select a multisample that you created in Sampling
mode or that you loaded in Disk mode.
Use “High Multisample” to select from 000–999.
EXB*: Multisamples from a separately sold EXB-PCM series
option board can be selected. “*” will indicate the type of
installed option.
The multisample number for “High Multisample” will
depend on the options that are installed.
The EXB* display will differ depending on the type of
option board.
If a program that uses a multisample from a separately
sold EXB-PCM series board is selected, but the neces-
sary multisample is not available because the corre-
sponding EXB-PCM (expansion board) is not installed,
the “High MS Bank” field will indicate “ROM.” In this
case, the program will not sound. By re-selecting the
multisample bank, you can make the program sound.
Each multisample has an upper limit, and may not pro-
duce sound when played above that limit.
S.Ofs (High Start Offset) [Off, On]
This specifies the point at which the multisample will begin
sounding. For some multisamples this parameter will have
no effect.
On (Checked): The sound will start from the start offset
location that is pre-determined for each multisample.
However when a RAM bank is selected, this will depend on
the selected multisample. If you select a multisample that
includes one of the following types of sample, checking this
item will cause playback to start from the Loop Start Address.
• A sample that was recorded (sampled) in Sampling
mode
• A sample whose Loop Start Address was edited in
Sampling mode after the sample was loaded in Disk
mode
• A sample whose Loop Start Address was specified
automatically when it was loaded as an AKAI, AIFF, or
WAVE file in Disk mode
Off (Unchecked): The sound will start from the beginning of
the multisample waveform.
Rev (High Reverse) [Off, On]
The multisample will be played in reverse. In the case of
ROM or optional (EXB-PCM series) multisamples that were
originally specified to loop, or in the case of multisamples
that were set to loop in Sampling mode, the multisample
will be played back in “one-shot” reverse mode. If the multi-
sample was originally set to reverse, it will playback with-
out change.
On (Checked): The multisample will playback in reverse.
Off (Unchecked): The multisample will playback normally.
Level (High Level) [0...127]
Specifies the level of the multisample.
Depending on the multisample, high settings of this
parameter may cause the sound to distort when a chord
is played. If this occurs, lower the level.
Low:
Specifies the OSC1 Low multisample.
The Low multisample will sound when the velocity is less
than the “Velocity SW L→H” (2.1–2a) setting.
Low MS Bank
Low Multisample
S.Ofs (Low Start Offset)
Rev (Low Reverse)
Level (Low Level)
☞ Refer to the corresponding item in “High.”
2.1–2a
2.1–2b
2.1–2e
2.1–2c
2.1–2d
2.1–2e