Korg Triton-Rack

Effect
199
a: L/R
When you select Up/Down for this parameter, the pitch shift
amount for the right channel will be reversed. If the pitch shift
amount is positive, the pitch of the left channel is raised, and the
pitch of the right channel is lowered.
096: Rotary SP OD
(Rotary Speaker Overdrive)
This is a stereo rotary speaker effect. It has an internal speaker
simulator that simulates overdrive (recreating the amp distor-
tion) and characteristics of the rotary speaker, producing a
very realistic rotary speaker sound.
a: (Sw)
This parameter determines how to switch on/off the overdrive
via a modulation source.
When “(Sw)” = Tggl (Toggle), overdrive is turned on/off each
time the pedal or joystick is operated.
Overdrive will be switched on/off each time the value of
the modulation source exceeds 64.
When “(Sw)” = Mmnt (Moment), overdrive is applied only when
you press the pedal or operate the joystick.
Only when the value for the modulation source is 64 or
higher, the overdrive effect is applied.
g
Feedback
Sets the feedback amount
–100...+100
☞ Fx:038
HiDamp (High Damp)
Sets the damping amount in the high range
0...100%
h
InLvl Mod (Input Level Dmod [%]) –100...+100
Sets the modulation amount of the input level
☞ Fx:037,
Src (Source)
Selects the modulation source for the input level
Off...Tempo
☞ Fx:037
i
Spread –100...+100
Sets the width of the stereo image of the effect sound
☞ Fx:043
j
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
–100...+100
a
OD (Overdrive)
Switches overdrive on/off.
Off, On
(Source) Off...Tempo
Selects the modulation source that switches overdrive on/off
(Sw) Tggl, Mmnt
Selects the switching mode of the modulation source that switches
overdrive on/off
☞
b
OD Gain (Overdrive Gain)
Determines the degree of distortion
0...100
Level (Overdrive Level)
Sets the overdrive output level
0...100
c
OD Tone (Overdrive Tone)
Sets the tonal quality of overdrive
0...15
SpSim (Speaker Simulation)
Switches speaker simulation on/off
Off, On
d
Mode (Mode Switch)
Switches between speaker rotation and stop
Rotate, Stop
(Source) Off...Tempo
Selects the modulation source that toggles between rotation and stop
(Sw) Tggl, Mmnt
Selects the switching mode of the modulation source that toggles
between rotation and stop
☞ Fx:040
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Mic Distance
Mic Spread
Horn/Rotor
Balance
D
-mod
D
-mod
D
-mod
D
-mod
Mode Switch: Rotate/Stop
Speed Switch: Slow/Fast
Manual Speed Control
On/Off
Speaker Simulation
Overdrive
Horn
Rotary Speaker
Rotor
+
e
Speed (Speed Switch) Slow, Fast
Switches the speaker rotation speed between slow and fast.
(Source) Off...Tempo
Selects the modulation source that toggles between slow and fast
(Sw) Tggl, Mmnt
Selects the switching mode of the modulation source that toggles
between slow and fast
☞ Fx:040
f
H/R.Bal (Horn/Rotor Balance) Rot, 1...99, Hrn
Sets the volume level balance between the high-range horn and low-
range rotor
ManuSp (Manual Speed Control) Off...Tempo
Sets the modulation source in case the rotation speed is changed
directly
☞ Fx:040,
g
Horn Accel (Horn Acceleration) 0...100
How quickly the horn rotation speed in the high range is switched
☞ Fx:040
Ratio (Horn Ratio) Stop, 0.50...2.00
Adjusts the (high-range side) horn rotation speed. Standard value is
1.00. Selecting “Stop” will stop the rotation
h
Rotor Accel (Rotor Acceleration) 0...100
Determines how quickly the rotor rotation speed in the low range is
switched
☞ Fx:040
Ratio (Rotor Ratio) Stop, 0.50...2.00
Adjusts the (low-range side) rotor rotation speed. Standard value is
1.0. Selecting “Stop” will stop the rotation
i
MicDistance 0...100
Distance between the microphone and rotary speaker
☞ Fx:040
Spread (Mic Spread)
Angle of left and right microphones
0...100
☞ Fx:040
j
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
–100...+100