Korg Triton-Rack

54
2.3–1: MOS..8 (MOSS T01–08)
2.3–2: MOS..16 (MOSS T09–16)
This page is displayed when the separately sold EXB-MOSS
option has been installed.
(
☞EXB-MOSS owner’s manual & p.251 “EXB-MOSS
option”)
3.1–1: MIDI..8 (MIDI T01–08)
3.1–2: MIDI..16 (MIDI T09–16)
Here you can make MIDI-related settings for each track.
3.1–1(2)a: Status, MIDI Channel, Bank(EX2) MSB/LSB
Status [INT, Off, BTH, EXT, EX2]
This sets the status of MIDI and the internal tone generator
for each track.
INT: The tone generator will sound in response to incoming
MIDI messages from a connected external MIDI device.
MIDI messages will not be transmitted. If RPPR or the
arpeggiator are assigned to a track that is set to INT, only
the TRITON-Rack will sound; MIDI data will not be trans-
mitted to an external device (i.e., the external MIDI device
will not sound). If the TRITON-Rack’s controllers are oper-
ated on the track specified as the “Control Track” (1.1–1a),
only the TRITON-Rack will be controlled, and MIDI mes-
sages will not be transmitted.
Off: The program will not sound, nor will MIDI data be
transmitted.
BTH: The operations of both INT and EXT will be per-
formed. If RPPR or the arpeggiator is specified for a track set
to BTH, the TRITON-Rack will sound and MIDI messages
will also be transmitted. If the TRITON-Rack’s controllers
are operated on the track specified as the “Control Track”
(1.1–1a), the TRITON-Rack will be controlled and the same
data will also be transmitted via MIDI.
EXT: MIDI messages will be transmitted without sounding
the internal program. If RPPR or the arpeggiator are
assigned to a track that is set to EXT, MIDI data will be
transmitted to an external device, but the tone generator of
the TRITON-Rack will not sound. If the TRITON-Rack’s
controllers are operated on the track specified as the “Con-
trol Track” (1.1–1a), MIDI messages will also be transmitted
to control the external device, but the TRITON-Rack itself
will not be controlled.
When you switch the multi, tracks that are set to EXT will
transmit program change, volume, panpot, portamento,
send 1, 2, post IFX pan, and post IFX send 1, 2 MIDI mes-
sages.
EX2: “Bank Select” will be enabled. Instead of the I-A–E-H
bank numbers that can be selected on the TRITON-Rack, the
bank number you specify here will be transmitted. In other
respects this is the same as EXT.
MIDI data is transmitted and received on the MIDI
channel that is specified separately for each track by
“MIDI Channel.”
MIDI Channel [01…16]
Specifies the MIDI channel that the track will use to transmit
and receive note data. Tracks set to INT which have the
same MIDI channel will sound and be controlled identically
when they receive MIDI data or RPPR data.
Bank(EX2) MSB [000...127]
Bank(EX2) LSB [000...127]
When “Status” is set to EX2, this sets the bank number that
will be transmitted. When “Status” is other than EX2, this
setting has no effect.
■ 3.1–1(2)b: UTILITY
☞ “Memory Status,” “Rename Multi,” “Delete Multi,”
“Copy From Multi,” “Copy From Combi,” “Load Tem-
plate Multi,” “Save Template Multi” (1.1–1c)
3.1–3: OSC..8 (OSC T01–08)
3.1–4: OSC..16 (OSC T09–16)
Indicates settings for each track.
3.1–3(4)a: Force OSC Mode, OSC Select,
Portamento
Force OSC Mode [PRG, Poly, Mono, LGT]
Selects the “Mode (Voice Assign Mode)” (PROG 2.1–1b) of
the program selected for each track 1–8, 9–16.
(
☞COMBI 3.1–2a)
OSC Select [Both, OSC1, OSC2]
Specifies the “Mode (Oscillator Mode)” (PROG 2.1–1a) of
the program selected for each track 1–8, 9–16. If the “Mode
(Oscillator Mode)” is Double, you can use this setting to
make only one or the other oscillator sound (
☞COMBI 3.1–
2a).
MULTI 2.3: MOSS
MULTI 3.1: Param1 (Parameter1)
3.1–1a
3.1–1b
Data from RPPR or Arp.
Operations on the TRITON-
Rack
Received data
Status Internal tone
generator
MIDI OUT Internal tone
generator
MIDI OUT
INT
●
×
●
—
EXT, EX2 ×
●
× —
BTH
●●●
—
3.1–3a
3.1–3b