Korg Triton-Rack

COMBI
1.1
2.12.22.33.13.23.33.44.14.24.34.46.17.17.27.3
41
These settings allow you to apply filters to the MIDI data
that will be transmitted and received by each timbre 1–8. For
example even if two timbres are being played by the same
MIDI channel, you can make settings so that the damper
pedal will apply to one but not the other.
On (Checked): Transmission and reception of MIDI data is
enabled.
When “Status” (3.1–1a) is INT, operations of the built-in
controllers or incoming MIDI data will apply the effect of
the checked item to the program of the corresponding tim-
bre. (The effect dynamic modulation function is not affected
by this setting.) When “Status” is EXT or EX2, operations of
the built-in controllers will transmit MIDI data on the chan-
nel of that timbre. MIDI transmission and reception settings
for the entire TRITON are made in “MIDI Filter” (GLOBAL
2.1–1b).
The MIDI 3 and MIDI 4 pages contain MIDI filters for
assignable controllers (whose function can be set by the
user), and if these are assigned to MIDI control changes, the
filter settings will affect those control changes.
If the function of the REALTIME CONTROLS knobs,
“SW1,” and “SW2” has been assigned to a MIDI control
change, the MIDI filters for these controllers (MIDI Filter 3,
4) will apply to those control changes. However if these
coincide with the control changes of MIDI Filter 1, 2, the
MIDI Filter 1, 2 settings will be given priority. Furthermore,
if the same control change has been assigned to two or more
controllers, the setting will be valid for that control change if
any single item is checked in either MIDI Filter 3 or 4.
Off (Unchecked): Transmission and reception of MIDI data
is disabled.
4.1–1: MIDI 1–1 (MIDI Filter 1–1)
4.1–1a: Program Change, After Touch
Program Change [Off, On]
Specifies whether or not MIDI program change messages
will be transmitted and received.
After Touch [Off, On]
Specifies whether or not MIDI after touch messages will be
received.
■ 4.1–1b: UTILITY
☞ “Write Combination,” “Solo Selected Timbre” (1.1–1d)
4.1–2: MIDI 1–2 (MIDI Filter 1–2)
4.1–2a: Damper CC#64, Portamento SW CC#65
Damper CC#64 [Off, On]
Specifies whether or not MIDI control change message #64
hold (damper pedal) messages will be transmitted and
received.
Portamento SW CC#65 [Off, On]
Specifies whether or not MIDI control change message #65
portamento on/off messages will be transmitted and
received.
■ 4.1–2b: UTILITY
☞ “Write Combination,” “Solo Selected Timbre” (1.1–1d)
4.2–1: MIDI 2–1 (MIDI Filter 2–1)
4.2–1a: JS+Y CC#01, JS–Y CC#02
JS+Y CC#01 [Off, On]
Specifies whether MIDI control change message #1 (selected
as assignment B for REALTIME CONTROLS [1]–[4] knobs,
or the +Y axis of the joystick on a TRITON etc.) will be trans-
mitted and received.
JS–Y CC#02 [Off, On]
Specifies whether MIDI control change message #2 (selected
as assignment B for REALTIME CONTROLS [1]–[4] knobs,
or the –Y axis of the joystick on a TRITON etc.) will be trans-
mitted and received.
■ 4.2–1b: UTILITY
☞ “Write Combination,” “Solo Selected Timbre” (1.1–1d)
COMBI 4.1: Ed–MIDI Filter1
4.1–1a
4.1–1b
COMBI 4.2: Ed–MIDI Filter2
4.1–2a
4.1–2b
4.2–1a
4.2–1b