36
Here you can set the Combination mode functions of the B-
mode functions of REALTIME CONTROLS knobs [1]–[4],
and “SW1,” “SW2.”
2.2–1: Ctrls (Controls)
2.2–1a: Knob B Assign
These settings assign functions (mainly various control
changes) to the “B” mode of the REALTIME CONTROLS
knobs [1]–[4] (
☞p.214 “Realtime Control Knobs B Assign
List”).
The functions you specify here will be controlled when you
operate the REALTIME CONTROLS knobs [1]–[4] in “B”
mode.
Since the REALTIME CONTROLS knob [1]–[4] function of
the B-mode assignments made for the program assigned to
each timbre are not valid for the combination, they must be
newly set by these parameters.
Knob1–B (Knob1–B Assign) [Off, ..., MIDI CC#95]
Knob2–B (Knob2–B Assign) [Off, ..., MIDI CC#95]
Knob3–B (Knob3–B Assign) [Off, ..., MIDI CC#95]
Knob4–B (Knob4–B Assign) [Off, ..., MIDI CC#95]
2.2–1b: SW1/2 Assign
These settings assign the function of the “SW1” and “SW2”
(
☞p.213 “SW1, SW2 Assign List”).
Since the function assignments of the “SW1” and “SW2”
made for the program assigned to each timbre are not valid
for the combination, they must be newly set by these param-
eters.
SW1 (SW1 Assign) [Off, ..., AfterT Lock :N/A]
SW1 Mode [Toggle, Momentary]
SW2 (SW2 Assign) [Off, ..., AfterT Lock :N/A]
SW2 Mode [Toggle, Momentary]
(☞PROG 2.2–1b)
■ 2.2–1c: UTILITY
☞ “Write Combination,” “Solo Selected Timbre” (1.1–1d)
This page is displayed if the separately sold EXB-MOSS
option is installed.
(
☞EXB-MOSS owner’s manual & p.251 “EXB-MOSS
option”)
3.1–1: MIDI
Here you can make MIDI settings for each timbre.
3.1–1a: Status, MIDI Channel, Bank(EX2) MSB/LSB
Status [INT, Off, EXT, EX2]
Specifies the status of MIDI and the internal tone generator
for each track.
INT: The TRITON-Rack will produce sound in response to
MIDI messages from a connected MIDI device. MIDI data
will not be transmitted. If the arpeggiator has been specified
for a timbre that is set to INT, only the internal tone genera-
tor will sound, and MIDI messages will not be transmitted
to an external device.
Off: The program will not sound, nor will MIDI messages
be transmitted.
EXT: The TRITON-Rack will not produce sound, but will
transmit MIDI messages to an external device. If the arpeg-
giator has been specified for a timbre that is set to EXT, MIDI
messages will be transmitted, but the internal tone generator
will not sound. If you operate the controllers of the TRI-
TON-Rack, the internal tone generator will not be con-
trolled, but MIDI messages will be transmitted to control an
external MIDI device.
EX2: “Bank (EX2) MSB” and “Bank (EX2) LSB” (3.1–1a) will
be enabled. Instead of the bank numbers for I-A–E-H that
can be selected on the TRITON-Rack, the bank numbers you
specify here will be transmitted via MIDI. In other respects
this is the same as EXT.
MIDI Channel [01...16, Gch]
Set the MIDI transmit/receive channel for each timbre 1–8.
Gch: The timbre will use the channel that has been selected
as the global MIDI channel “MIDI Channel” (GLOBAL 2.1–
1a).
When “Status” is INT, MIDI messages will be received on
the channel you specify here. If this is set to EXT or EX2,
playing the TRITON-Rack will transmit MIDI messages on
the MIDI channel specified here. (Messages will also be
transmitted simultaneously on the global MIDI channel.)
COMBI 2.2: Ed–Ctrl
COMBI 2.3: Ed–MOSS
2.2–1a
2.2–1c2.2–1b
COMBI 3.1: Ed–Param1
3.1–1a
3.1–1b
The TRITON-Rack’s Controllers
Arpeggiator
Tone
generator
MIDI IN
INT
The TRITON-Rack’s Controllers
Arpeggiator
MIDI IN
EXT, EX2
MIDI OUT
To Next Page
Loading...
