Korg Triton-Rack

Effect
193
083: Wah–AmpSim
(Wah/Auto Wah – Amp Simulation)
This effect combines a mono-type wah and an amp simula-
tion. You can change the order of the effect connection.
084: Deci–AmpSim
(Decimator – Amp Simulation)
This effect combines a mono-type decimator and an amp sim-
ulation. You can change the order of the effect connection.
085: Deci–Comp
(Decimator – Compressor)
This effect combines a mono-type decimator and a compres-
sor. You can change the order of the effect connection.
a
[WAH] Freq Btm (Frequency Bottom)
Sets the lower limit of the wah center frequency
0...100
☞ Fx:009
Top (Frequency Top)
Sets the upper limit of the wah center frequency
0...100
☞ Fx:009
b
Swp Mode (Sweep Mode) Auto, Dmod, LFO
Selects the control from auto-wah, modulation source, and LFO
☞ Fx:009,
Src (Source) Off...Tempo
Selects the modulation source for the wah when Swp Mode=Dmod
c
lfoF (LFO Frequency)
Sets the LFO speed
0.02...20.00Hz
d
Resonance
Sets the resonance amount
0...100
LPF (Low Pass Filter)
Switches the wah low pass filter on and off
Off, On
e
[AMP] Amplifier Type
Selects the type of guitar amplifier
SS, EL84, 6L6
f
[Routing] WAH → AMP, AMP → WAH
Switches the order of the wah and amp simulation connection
g
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
–100...+100
a
[DECI] Pre LPF Off, On
Turn the harmonic noise caused by lowered sampling on and off
☞ Fx:014
b
High Damp
Sets the ratio of high-range damping
0...100%
c
Sampling Freq (Sampling Frequency)
Sets the sampling frequency
1.00k...48.00kHz
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Routing
Amp Simulation
Amp Simulation Filter
Wah/Auto Wah
Wah
D
-mod
Envelope
Sweep Mode
D-mod
Auto
LFO
LFO
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Decimator
Routing
Amp Simulation
Amp Simulation Filter
Pre LPF
High Damp
Output Level
Decimator
Resolution
d
Resolution
Sets the data bit length
4...24
☞ Fx:014
e
Level (Output Level)
Sets the decimator output level
0...100
☞ Fx:014
f
[AMP] Amplifier Type
Selects the type of guitar amplifier
SS, EL84, 6L6
g
[Routing] DECI→AMP, AMP→DECI
Switches the order of the wah and amp simulation connection
h
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
–100...+100
a
[DECI] Pre LPF Off, On
Turn the harmonic noise caused by lowered sampling on and off
☞ Fx:014
High Damp
Sets the ratio of high-range damping
0...100%
b
Sampling Freq (Sampling Frequency)
Sets the sampling frequency
1.00k...48.00kHz
c
Resolution
Sets the data bit length
4...24
☞ Fx:014
d
Level (Output Level)
Sets the decimator output level
0...100
☞ Fx:014
e
[CMP] Sensitivity
Sets the sensitivity
1...100
☞ Fx:002
f
Attack
Sets the attack level
1...100
☞ Fx:002
Level (Output Level)
Sets the compressor output level
0...100
☞ Fx:002
g
[Routing] DECI→CMP, CMP→DECI
Switches the order of the decimator and compressor connection
h
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Decimator
Routing
Pre LPF
High Damp
Output Level
Decimator
Resolution
Compressor
Comp
Output Level
Envelope - Control