Korg Triton-Rack

107
GLOBAL
1.1
2.1 3.1 4.1 5.1 6.1
5. Global mode
In Global mode you can make settings that affect the entire
instrument, such as master tuning, MIDI, and memory pro-
tect. You can also edit user scales, drum kit setups, and user
arpeggio patterns.
If you want the settings you make in Global mode to be
backed up when the power is turned off, you must
write them into memory. To write your settings, use the
Utility “Write Global Setting,” “Write Drum Kits,” or
“Write Arpeggio Patterns.”
By pressing the [WRITE] key, you can access “Update
Global Setting,” “Update Drum Kits,” and “Update
Arpeggio Patterns.” These commands will simulta-
neously write the edited content.
For details on selecting pages and parameters, refer to Pro-
gram mode “PROGRAM PAGE MENU” p.1.
1.1–1: Basic
1.1–1a: Basic
Master Tune (Master Tune [Cent])
[–50cent (427.47Hz)…+50cent (452.89Hz)]
This adjusts the overall tuning of the entire TRITON-Rack in
one-cent units (semitone = 100 cents) over a range of ±50
cents. With a setting of 0, the frequency of A4 will be 440 Hz.
The A4 pitch given here is when Equal Temperament is
selected as the scale. If a different scale is selected, A4
may not be 440 Hz.
Key Transpose [–12…+12]
This adjusts the pitch in semitone steps over a ±1 octave
range.
In Program, Combination, and Multi modes, the tuning
of each program, timbre (Combination mode) or track
(Multi mode) can be adjusted relative to the “Master
Tune” setting by using MIDI RPN Fine Tune messages.
Transpose can be adjusted relative to the “Key Trans-
pose” value by using MIDI RPN Coarse Tune messages.
In Program mode, these messages are received on the
global MIDI channel specified by “MIDI Channel” (2.1–
1a). In other modes, these messages are received on the
MIDI channel of the individual timbre (Combination
mode) or track (Multi mode). (
☞”Detune”: COMBI 3.1–
3a, MULTI 3.1–5a/6a)
“Master Tune” can be controlled by the MIDI universal
system exclusive message Master Fine Tuning (F0, 7F,
nn, 04, 03, vv, mm, F7: nn=MIDI channel, vv/mm=
value).
“Key Transpose” can be controlled by the MIDI univer-
sal system exclusive message Master Coarse Tuning
(F0, 7F, nn, 04, 04, vv, mm, F7: nn=MIDI channel, vv/
mm=value).
These messages are received on the global MIDI chan-
nel specified by “MIDI Channel” (2.1–1a).
GLOBAL PAGE MENU
Sys. 1.1: System Basic settings for the entire TRITON-
Rack. AUDIO INPUT settings for other
than Sampling mode. (
☞p.107)
MIDI 2.1: MIDI MIDI settings for the entire TRITON-
Rack. (
☞p.111)
U.Scl 3.1: User Scale Scale settings created by the user. You
can specify 16 types of octave scale,
and one full-range scale. (
☞p.114)
U.Cat 4.1: Category Name Edit category names for programs and
combinations. (
☞p.115)
DKit 5.1: DKit Edit drum kits. (
☞p.116)
Arp 6.1: Arp.Pattern Edit user arpeggio patterns. (
☞p.119)
GLOBAL 1.1: System
1.1–1a
1.1–1d1.1–1c1.1–1b