PROG
1.1
2.12.22.33.14.14.25.15.25.36.17.17.27.3
9
Decay: Adjusts the decay times of the filter EG and amp
EG. This adjustment will be added to the “D (Decay
Time)” of “Filter 1 EG,” “Filter 2 EG,” “Amp 1 EG,” and
“Amp 2 EG.”
4 Press the [F8] (“Done”) key to execute, and close the dia-
log box.
Please be aware that the Compare function is not avail-
able for this command.
2.1–3: OSC2
This will appear when “Mode (Oscillator Mode)” (2.1–1a) is
set to Double.
For details on the settings and function of the parameter,
refer to “2.1–2: OSC1.”
2.1–4: V.Zone (Velocity Zone)
Specifies the range of velocities that will sound oscillator 1
and 2. By using these settings in conjunction with the
“Velocity SW L→H” (2.1–2a) setting of each oscillator, you
can specify the velocity ranges for the High and Low multi-
samples or drum kits.
It is not possible to set the Bottom Velocity greater than
the Top Velocity, nor the Top Velocity less than the Bot-
tom Velocity.
2.1–4a: OSC 1/2 Velocity Zone
OSC1 Bottom [001...127]
Sets the minimum velocity value that will sound oscillator 1.
OSC1 Top [001...127]
Sets the maximum velocity value that will sound oscillator
1.
OSC2 Bottom [001...127]
Sets the minimum velocity value that will sound oscillator 2.
OSC2 Top [001...127]
Sets the maximum velocity value that will sound oscillator
2.
You can hold down the [ENTER] key and play a note on
a connected MIDI device to input these values.
■ 2.1–4b: UTILITY
☞ “Write Program” (1.1–1d), “Copy Oscillator,” “Swap
Oscillator” (2.1–1d)
2.1–5: Audit. (Audition)
When selecting preloaded programs, you can play back a
pre-specified riff (phrase) that is suitable for the sound of
that program. This is called the Audition function.
When you press the [AUDITION] key to turn it on, the audi-
tion riff will play back repeatedly. This allows you to verify a
program or edit it even when a MIDI keyboard is not con-
nected.
Here you can select the audition riff and specify the transpo-
sition.
2.1–5a: Audition Riff, Transpose
Audition Riff [000: Off...382: Name]
Selects the audition riff. The TRITON-Rack contains 382
audition riffs suitable for a variety of instruments and musi-
cal genres. (
☞“VNL”)
With a setting of 000: Off, no riff will be played.
Transpose [–24...+24]
Adjusts the pitch of the audition riff in semitone steps.
It is not possible to change the playback tempo of the
audition riff. Nor is it possible to set the arpeggiator
tempo while the audition riff is playing.
The arpeggiator will be turned off while the audition
riff is playing.
■ 2.1–5b: UTILITY
☞ “Write Program” (1.1–1d)
These settings specify the B-mode functions of REALTIME
CONTROLS knobs [1]–[4] in Program mode. and “the func-
tions of the SW1,” the “SW2.”
2.2–1: Ctrls (Controls)
2.2–1a: Knob B Assign
Here you can Assign functions (mainly various types of con-
trol change) to the B-mode of the REALTIME CONTROLS
knobs [1]–[4] (
☞p.214 “Realtime Control Knobs B Assign
List”).
The functions you set here will take effect when you operate
the REALTIME CONTROLS knobs [1]–[4] in B-mode.
2.1–4a
2.1–4b
PROG 2.2: Ed–Ctrl
2.1–5a
2.1–5b
2.2–1a
2.2–1c2.2–1b
To Next Page
Loading...
