LulzBot TAZ 5 - Page 168

To Next Page

To Previous Page

INDEX

Tweak at Z, 35

Updating Firmware, 43

USB cable, 51

View Options, 19

warnings, viii

warping, 150

warranty, 158

website, 136

Windows, 13, 49, 54, 55

wires, viii

Xray, 21

Z hop, 37

Z Wobble, 134

168

Main Page

Table of Contents3
Warnings9
- Safety Information9
- Lulzbot9
- Hazards and Warnings10
- Support11
Printer Software13
- Software Overview14
- Software Types14
- Installing Drivers15
- Cura15
- Quick Print Settings17
- High Detail17
- Material Selection18
Options after Selecting Model19
Rotating Your Model20
- View Options21
Scaling Your Model21
View in Normal Mode22
View in Overhang22
View in Ghost23
View in Xray23
View in Layers24
Viewing Cumulative Layers24
- Starting Your First Print25
Viewing Specific Layers25
Control Screen26
- Removing Your First Print28
- Full Settings28
- Basic Tab Options29
View in Full Settings29
Differences in Layer Height30
- Shell Thickness30
Support Types32
- Advanced Tab Options33
- Retraction Distance34
Cutoff Example35
- Dual Extrusion Overlap35
- Travel Speed35
- Plugins36
- Outer Shell Speed36
- Inner Shell Speed36
- Start and End Gcode Settings37
View of Plugins37
- Expert Settings38
- Retraction38
View Expert Settings38
- Skirt39
- Minimum Travel39
- Line Count39
- Cool40
- Start Distance40
- Minimal Length40
- Support41
- Black Magic42
- Brim42
- Raft42
- Extra Margin43
- Line Spacing43
- Fix Horrible44
- Surface Layers44
- Extensive Stitching44
- Dual Extrusion45
- First Dual Print47
Before Merge48
After Merge49
- Setting Dual Temps49
- Printrun50
Printrun Application for 3D Printer Control50
- Using Printrun52
Printrun Functions54
Movement Controls54
- CAD and 3D Modeling Software56
- Alternative Printer Host Software57
Slic3R59
- Introduction60
- Getting Slic3R61
- First Print62
Configuration Wizard: Welcome Screen64
Configuration Wizard: Firmware Type65
Configuration Wizard: Bed Size66
Configuration Wizard: Nozzle Diameter67
Configuration Wizard: Filament Diameter68
Configuration Wizard: Extrusion Temperature69
Configuration Wizard: Bed Temperature70
Configuration Wizard: End71
The Important First Layer72
Shapesmith Online CAD Tool75
Plater76
Minimug Model77
STL File Loaded77
- Simple Mode79
Simple Mode: Print Settings80
An Example of Insufficient Top Layers81
Creating a Vase from a Solid Model82
An Example of an Object Printed with Support Material83
An Example of Brim84
Simple Mode: Filament Settings85
Simple Mode: Printer Settings86
- Expert Mode88
Expert Mode Speed Options89
Infill Pattern Settings92
Infill Pattern: Line (344.51Mm / 5M:20S)92
Infill Pattern: Rectilinear (350.57Mm / 5M:23S)92
Infill Pattern: Concentric (351.80Mm / 5M:30S)93
Infill Pattern: Honeycomb (362.73Mm / 5M:39S)93
Infill Pattern: Hilbert Curve (332.82Mm / 5M:28S)93
Infill Pattern: Archimedean Chords (333.66Mm / 5M:27S)93
Infill Pattern: Octagram Spiral (318.63Mm / 5M:15S)94
Infill Pattern Comparison in a Complex Object. Left to Right: Honeycomb, Line94
Infill Patterns at Varying Densities95
- Left to Right95
- 20%,40%,60%,80%. Top to Bottom: Honeycomb, Concentric95
Infill Advanced Settings96
Retraction Settings97
Skirt Settings99
Cooling Strategy101
Cooling Advanced Settings102
- Support Material103
Support Structure Options104
Minimug Model, Tilted105
Support Infill Pattern: Rectilinear105
Support Infill Pattern: Rectilinear Grid105
Support Infill Pattern: Honeycomb106
Example of Pattern Angle Rotated106
Multiple Extruder Options - Printer Settings Tab (General). Note the Two Extruders Defined in the Left-Hand Pane107
Plater with Multiple Filament Options108
Multiple Extruder Options - Print Settings Tab109
Multiple Extruder Options - Tool Change G-Code110
Extrusion Widths Options111
Example Model Highlighting Use Case for Variable Layer Heights112
Example with Normal Layer Height113
Variable Layer Height Options - Info114
Variable Layer Height Options - Layers115
Example with Variable Layer Height115
Example Print with Variable Layer Height116
Example with Skipped Layers116
- Configuration Organization117
Saving a Profile118
Deleting a Profile118
- Repairing Models119
Freecad Part Repair119
- Advanced Topics120
Sequential Printing Options120
The Clearance Cylinder Around an Extruder121
Post-Processing Script Option127
Example Post-Processing Script to Display Slic3R Environment Variables127
Example Post-Processing Script to Print each Line to Output128
Extrusion Width129
Bridging Filament Shape130
Extrusion Shape131
No Path Overlap131
- Sane Defaults132
- Troubleshooting133
- Dimension Errors133
Holes Made through Polygonal Segments134
Variable Filament Diameter Changing Layer Stacking135
- Slic3R Support138
- Printing with the Graphic LCD141
Printing with the Graphic LCD142
- GLCD Controller, Cura or Printrun Host142
- Multiple Connections142
- Putting Print Files on the SD Card143
GLCD Info Screen143
- Printing with the Graphic LCD144
Main Menu145
Maintaining Your 3D Printer147
- Overview148
- Smooth Rods148
- Lead Screw Drive Rods148
- PEI Surface148
- Hobbed Bolt149
- Belts149
- Hot End149
- Electronics149
Advanced Usage151
- Intro152
- Changing Nozzles152
- Bed Adhesion152
- Using 1.75Mm Filament153
Hardware and Software Source Code155
Printer Support158
- Community158
Warranty Information159
- Warranty160
- Extended Warranty160
Contact Information161
- Support162
- Sales162
- Websites162
Index163
Glossary169

LulzBot TAZ 5 - Page 168

Table of Contents

Other manuals for LulzBot TAZ 5

Related product manuals