LUMENIS VersaPulse PowerSuite - SELECTED PART NUMBERS; FIELD SERVICE BULLETINS; SCHEMATICS & DRAWINGS

178 pages

Save Page as PDF

To Next Page

To Previous Page

5.6 Remove/Replace Procedure

5.7 Troubleshooting

6.0 SELECTED PART NUMBERS

7.0 FIELD SERVICE BULLETINS

8.0 SCHEMATICS & DRAWINGS

VersaPulse



PowerSuite Service Manual Table of Contents 0636-499-00 REV. C

Main Page

Table of Contents5
General Information5
Installation5
Theory of Operation5
General Information11
Use of this Manual11
Conventions Used in this Manual11
Serial Numbers12
Certification of Compliance13
Service Information & Fda Compliance13
Rear View14
Front View15
Installation17
Site Inspection17
Unpack & Inspect Laser18
Verify the AC Mains Voltage at the Site18
Check the Crate/Carton for any Shipping Damage18
Remove the Console and Accessories from the Crate18
Configure AC Control PCB19
Move the System to Its Installation Location19
Open/Remove Covers and Do a Visual Inspection of the Interior19
Locate the AC Control PCB and Identify TB5 & TB220
Locate the Large Brown Wire in TB5-1 and Position the Other End in TB220
Locate the Two Small Blue Jumper Wires in TB7 (Bottom Right)20
Add Coolant21
Turn on21
Record the Voltage Range on the Certification Report21
Connect to AC Service21
Customer Demonstration22
Product Specification23
Calibration, Adjustment and Alignment27
Safety Precautions28
Optical Alignment29
Folding Mirror Alignment29
YAG Channel Alignment30
Making Test Burns30
Using the Test Aperture32
Using the Cross Hair Aperture32
Adjusting the YAG Channel Optics33
Relay and Plano Mirrors Diagram34
Resonator Alignment35
Servo Mirror Alignment37
Servo Mirror Installation38
Fiber Alignment39
Pyro Detector Alignment41
Electrical Adjustment42
Aiming Beam Alignment42
Voltage Configuration42
AC Configuration on the AC Control PCB43
Fan Speed Adjustment44
Mechanical Adjustments45
Speaker Volume Adjustment45
External Fiber Sense Switch Adjustment45
SMA Fiber Port Assembly46
Energy Monitor and Auto Calibration47
Blastshield Sense Switch Adjustment47
System Optimization Check50
Fiber Alignment Test50
Examining the Test Fiber Burn52
Verify Calibration - Delivered Power out of the Fiber52
Flashlamp Performance Check53
Operational and Safety Checkout54
Check the Circuit Breaker54
Check the Keyswitch54
Check the E-Stop Button55
Check the BRH Plug55
Check the Blastshield55
Check the Fiber Switch55
Check the Flowswitch56
Check the Footswitch56
Check the LCD Color Display56
Check the Remote Control Panel56
Periodic Maintenance Requirement58
Anually (as Required)58
Theory of Operation59
Operational Overview59
Functional Overview60
Power Switching, Conditioning, Distribution61
Flash Lamp Supply Circuits62
Input Power64
Power Switching, Conditioning, Distribution64
To Turn on65
Circuit Breaker On, Keyswitch off65
Turn on Sequence65
Shutdown66
Low Voltage Power Supplies66
Cooling67
Components70
Control Electronics71
Microprocessor72
Digital I/O Circuits74
D/A & A/D Conversion Circuits75
DC Power Supply Monitor Circuits75
Audio Amplifier Circuit75
Shutter/Footswitch/Remote Interlock Circuits76
Servo Motor Control Circuit77
HVPS & Control Circuits78
Energy Monitor Circuits79
User Interface and Remote Control Circuits81
Aiming Diode Laser Circuit81
Fiber and Blast Shield Position Sense Circuits82
Service Attenuator Circuit82
Low Energy Attenuator Circuit83
Flashlamp Power Circuits84
Optics85
YAG Cavity86
Multiplexing Optics86
Common Beam Path86
Low Energy Attenuator86
Software87
Aiming Beam Diode and Combiner Optic87
Wedge Optic87
Service Attenuator87
Normal System Operation88
System States to be Implemented89
Startup89
Standby90
Ready State90
Treatment State91
System Monitoring92
Operational Monitoring93
System Monitoring During Standby State93
System Monitoring During Ready State95
System Monitoring During Treatment95
Testing Safety Systems96
Delivering Treatment97
Error Handling99
System Messages101
User Statistics101
Service Mode102
Service Firing102
System Calibration102
NVRAM Initialization102
Language Selection103
Display Calibration Graphs103
Display Pulse Energy Graphs103
Fire for Fiber Position Check103
Service Mode Screens104
Display System Information104
Service 2105
Energy Plots105
Calibration Plots105
Service Mode Controls and Displays106
Fiber Centration106
Pulse Rate106
Flashlamp Voltage107
Holmium Pump Energy107
Nd:yag Lamp Current108
Ready/Standby108
Laser Rod Enable/Disable108
Laser Pulse Energy108
Initialize NVRAM Button109
Next Service Screen Button109
Attenuator Position109
Shutter Mode109
Plot Calibration110
Plot Calibration Data110
Calibration Formula Display110
Calibration Value Table110
Centration Shot Limit111
Fire Centration111
Laser Rod Type Display111
Troubleshooting113
Service Philosophy113
Precautions114
Interior Access and Parts Location115
Front Views116
CPU PCB Layout117
Low Voltage Power Supply Chart118
Removing the Top Cover119
Optics Bench and Laser Head Layout120
YAG Cavity Layout121
Servo Motor PCB122
Attenuator PCB123
Interior View, Right Side124
AC Control PCB Layout125
Fan Speed Controller PCB125
Service Mode Software Routines126
Interior View, Left Side126
First Service Screen127
Second Service Screen128
Third Service Screen - Report Screen129
Fourth Service Screen - Plot Energy Screen130
Fifth Service Screen - Plot Cal Screen131
Sixth Service Screen - Centration Screen132
Fault Isolation133
Seventh Service Screen - Power-Up Screen133
Turn on and Shut down Fault Isolation134
“No Fault Code Reported” Fault Isolation134
“Fault Code Reported” Fault Isolation135
Test Points and LED Arrangement140
Controller PCB Leds146
Remove/Replace Procedure150
Flashlamp Replacement150
Controller PCB Replacement151
Troubleshooting Guide153
Water Filter Replacement153
Optics and Optics Related Components Troubles154
Pcbs Troubles155
Power Supply Troubles155
Other Components Troubles156
Temperature Troubles156
Blastshield157
Fiber Endface158
Selected Parts159
Special Tools159
User Replaceable Sub-Assemblies159
Control System Printed Circuit Boards160
High Voltage Power Supply160
Chassis and Skins160
Chassis Electrical/Major Sub-Assemblies161
Cable Sets/Harnesses162
Cooling System Parts162
Optics, Common163
Optics, Holmium163
Optics, Neodymium163
Field Service Bulletins165
Versapulse Powersuite Field Service Bulletin Index167
Coding Instructions: Versapulse Product Line168
VP Coding Instructions169
Versapulse Codes170
Versapulse Powersuite FSB #1173
Power Supply Controller Board Diagram173
Versapulse Powersuite FSB #2175
Schematics and Drawings List177

LUMENIS VersaPulse PowerSuite - SELECTED PART NUMBERS; FIELD SERVICE BULLETINS; SCHEMATICS & DRAWINGS

Table of Contents

Related product manuals