Motion Control Engineering Nidec iControl - Page 444

Index-5
Earthquake Run message 6-30
Earthquake Shutdown message 6-30
Edit a parameter on the iBox 7-4
Edit a parameter using iView 8-19
Editing a configuration file 8-23
Editing displays 8-39
EEPROM Device Error message 6-31
Electrical Governor Test 4-44
Elevator Recall Operation (Switch ‘n’) message 6-31
ELEVATOR RECALL SW’n’ message 6-31
EM BK UIM RESET STUCK message 6-32
EMERG ALARM ACTIVATED message 6-31
EMERG BRAK LEG 2 SHORT message 6-32
EMERG BRAKE OK OPEN message 6-32
EMERG BRAKE TRIPPED message 6-32
EMERG BRK LEG 1 SHORT message 6-32
EMERG POWER RECALL message 6-33
EMERG POWER RUN message 6-34
EMERG POWER SHUTDOWN message 6-34
EMERG PWR NO COMM message 6-33
Emergency Alarm Acknowledged message 6-31
Emergency Alarm Activated (Alarm button) message 6-31
Emergency Alarm Activated (Car delayed with doors closed)
message 6-31
Emergency Alarm Activated (In-car stop switch) message 6-
31
Emergency Alarm Activated (Safety opened) message 6-31
Emergency Alarm Activated message 6-31
Emergency Alarm Deactivated without Acknowledgment
message 6-31
Emergency Brake Board Quick Reference 6-90
Emergency Brake Leg 1 Short Fault message 6-32
Emergency Brake Leg 2 Short Fault message 6-32
Emergency Brake OK open message 6-32
Emergency Brake OK open Off message 6-32
Emergency Brake Test - Unintended Motion 4-47, 4-48
Emergency Brake Test - Unintended Motion for Machine
Brake 4-48
Emergency Brake Test - Unintended Motion for Rope Gripper
4-47
Emergency Brake Tripped message 6-32
Emergency Brake UIM Reset Button Stuck message 6-32
Emergency Dispatch message 6-32
Emergency Dispatch Off message 6-32
Emergency Medical Service Bypassed message 6-32
Emergency Medical Service Deactivated message 6-32
Emergency Medical Service In-Car Activated (Switch ’n’)
message 6-33
Emergency Medical Service Recall Activated (Switch ’n’) mes-
sage 6-33
Emergency power 5-13
Emergency Power Activated message 6-33
Emergency Power and no communication with group mes-
sage 6-33
Emergency Power Deactivated message 6-33
Emergency power profile 4-13
Emergency Power Recall (In Service) message 6-34
Emergency Power Recall message 6-33
Emergency Power Run message 6-34
Emergency Power Shutdown message 6-34
Emergency slowdown profile 4-13, 4-52
Emergency Stop Input Activated message 6-34
Emergency Stop Input Deactivated message 6-34
EMERGENCY STOP INPUT message 6-34
Emergency Stop switch 2-13
Emergency Terminal Limit (ETS) 4-8
Emergency Terminal Overspeed 4-54
Emergency Terminal Switch Overspeed Tests 4-53
Empty Car Tests, preparing for final adjustments 3-13
Empty load detection 4-30
Empty load threshold 4-31, 4-33
EMS In-car (Switch ‘n’) message 6-33
EMS Recall (Switch ‘n’) message 6-33
Enable switch, iBox control 7-11
Encoder Signal test point, description 9-4
Environmental Considerations 2-3
Environmental Limits specification 9-2
EP RECALL (IN SERVICE) message 6-34
EQ board, Earthquake sensor 3-6
EQ Reset 3-6
ESC, Car Panel Emergency Stop switch input 6-110, 9-7
ETA Mode Activated message 6-34
Ethernet address verification, iBox 7-9
Ethernet connections 2-4
Event Log
viewing on the iBox 7-7
EXCESS BRAKE FDBK FLT message 6-34
EXCESS MF FDBK FAULT message 6-35
EXCESS RELEVELS FAULT message 6-35
EXCESS RESTARTS FAULT message 6-35
Excessive Brake Feedback Fault message 6-34
EXCESSIVE FAULTS message 6-35
Excessive Faults Shutdown message 6-35
Excessive Faults Warning message 6-35
EXCESSIVE FLTS WARN message 6-35
Excessive Motor Field Feedback Fault message 6-35
Excessive Motor Noise 4-15
Excessive Relevels Fault message 6-35
Excessive Restarts Fault message 6-35
Excessive Restarts Warning message 6-35
Exercise Operation Activated message 6-36
Exercise Operation Deactivated message 6-36
EXERCISE OPERATION message 6-36
exiting Construction Mode 3-9
F
F DPM OPEN-GS CLOSED message 6-40
F DR CLS FLT REC FAIL message 6-39
F1 help, accessing online help 8-24
FAULT BYPASS SW ON message 6-36
Fault Bypass Switch On message 6-36
Fault Bypass Switch Timed Out Fault message 6-36
Fault Reset, iBox control 7-3
Fault, iBox status LED 7-10
Fault/Function Bypass switch, iBox control 7-11
Field Active Status test point, description 9-4
Field Command (Control) test point, description 9-4
field connections 9-6–9-11
Field Control Path test point, description 9-4
Field Current Feedback test point, description 9-4