NF DP Series - User Manual

Using Limiter, Setting Limiter97
- Use Peak Current Limiter97
- Using RMS Current Limiter99
- Using Voltage Setting Range Limit101
- Using Frequency Setting Range Limit102
- About Wattage Limiter104
- Table 4-1 Wattage Limiter Value Per Phase (Reference Value, Unit: W)104
Using Sequence Function105
- Basics105
- Figure 4-1 Step-Control Parameters and Intra-Step Parameters106
- Figure 4-2 Step Behavior107
- Parameters of Sequence Function108
- Table 4-2 Parameters of Sequence Function108
- Figure 4-3 Stop Phase110
- Example of Output Using Sequence Function111
- Process Flow in a Step111
- Figure 4-4 Example of Sequence111
- Table 4-3 Example of Editing Sequence111
- Figure 4-5 Process Flow in Sequence Step112
- Figure 4-6 Branch Operation/Stop Operation112
- Edit a Sequence113
- Load a Sequence116
- Execute a Sequence120
- Save a Sequence124
- Clear/Rename Sequence128
- Set so as the Sequence Function Is Selected at Power-On132
- Sequence Control by CONTROL I/O133
- Screen Overview133
- Figure 4-7 Sequence Edit View134
- Figure 4-8 Sequence Control View (Output off State)134
- Figure 4-9 Sequence Control View (Output on State/Sequence in Execution)134
- Change Output Parameter During Output on135
- Figure 4-10 Sequence Control View (Output on State/Sequence Stopped)135
Using Power Fluctuation Testing (Simulation) Function137
- Basics137
- Function137
- Simulation Function Parameters139
- Figure 4-11 Simulation Function Steps139
- Table 4-4 Simulation Function Parameters139
- Table 4-5 Simulation Function Steps and Settable Step Parameters140
- Output Examples Using Simulation Function141
- Figure 4-12 Voltage Dip Simulation Example141
- Table 4-6 Voltage Dip Simulation Edit Example141
- Figure 4-13 Voltage Change Simulation Example142
- Table 4-7 Voltage Change Simulation Edit Example142
- Process Flow in a Step143
- Editing Simulation143
- Figure 4-14 Process Flow through Simulation Steps143
- Figure 4-15 Stop Operation143
- Loading a Simulation146
- Executing Simulation149
- Saving Simulation151
- Clear/Rename Simulation155
- Set so as the Simulation Function Is Selected at Power-On159
- Simulation Control by CONTROL I/O160
- Screen Overview160
- Figure 4-16 Simulation Edit View161
- Figure 4-17 Simulation Control View (Output off State, Simulation Stopped)161
- Figure 4-18 Simulation Control View (Output on State, Simulation Running)161
Measuring Harmonic Current162
- Harmonic Current162
- Figure 4-19 Simulation Control View (Output on State, Simulation Stopped)162
- Figure 4-20 Current Waveform Containing Many Harmonic Components162
- Basics163
- Measured Value Display Method163
Measuring Inrush Current164
- Inrush Current164
- Figure 4-21 Inrush Current Example164
- Basics165
- Measurement Method165
- Measurement Tips166
Using Clipped Sine Wave166
Figure 4-22 Clipped Sine Wave166
Table 4-8 Different Output Voltage Settings Depending on Clip Depth Setting Method167
Outputting Arbitrary Waveform169
- Basics169
- Arbitrary Waveform Creation Procedure170
- Arbitrary Waveform Creation Example170
- Transferring Arbitrary Waveform170
- Outputting Arbitrary Waveform173
Using Memory Function174
- Basic Setting Memory175
- Arbitrary Waveform Memory182
- Sequence Memory186
- Table 4-9 Content Saved in Sequence Memory186
- Simulation Memory187
- Table 4-10 Content Saved in Simulation Memory187
Using USB Memory Function188
Figure 4-23 USB Memory Folder Structure188
Using Monitor Function189
Using Remote Sensing Function192
Figure 4-24 Sensing Input Terminals in Multi-Phase Model193
Using AGC Function195
Using Autocal Function198
Adjusting DC Offset202
Table 4-11 Setting Range of DC Offset Adjustment Value202
Using for Unbalanced Polyphase Output204
Using as DC Power Supply206
Setting Voltage Using External DC Input Signal208
- Using External Signal in AC-VCA Mode208
- Using External Signal in DC-VCA Mode210
Control Using External Control Function211
- Using CONTROL I/O212
- Table 4-12 CONTROL I/O Pin Assignment213
- Table 4-13 Step Sync Code213
- Table 4-14 Memory Specification213
- Control of DIP217
Synchronizing the Output Frequency with the Power Line or the External Signal219
Figure 4-25 the Control Cable Connection of DP030S and DP4172(DIP)219
Amplifying the External Signal Input221
Turning the Output on or off Rapidly222
Table 4-15 the Output Terminal Impedance in the Output off State When the Activation of222
Enabling Automatic Output-On at Power-On224
Figure 4-26 the Message Window to be Shown before the Automatic Output-On after the224
Using the Emission CO Calculator225
Using the Emission CO2 Calculator225
Power Unit Energization Setting (Using under the Restricted Rated Power)227
Power Unit Energization Setting227
Restricted Rated Power)227
Key Lock229
Beep229
Changing the Background Color and the Contrast of the Screen230
Of the Screen230
Restoring to the Factory Default Setting (Reset)231
Table 4-16 Setting Items to be Reset231

5 Description of Screen and Menu236

Brand	NF
Model	DP Series
Category	AC Power Distribution
Language	English

NF DP Series - User Manual

Table of Contents

NF DP Series Specifications