169
Determining the Error from the Status
Section 7-3
Status Directory Tree
TC4
bits 0 to 3: Not used.
EEPROM Error
Calibration Error
Setting Value Error
Not used.
Configured Registration Data Error
Device Information Data Error
Model Information Mismatching Error
Device A Status
Device Error Status
Device Error
Undefined Expand Unit
Not used.
Too Many Expand Units
Expand Unit Failure
Expand Unit Connection Fault
Configuration Error A Status
Configuration Error
Expand Unit 1 Error
Expand Unit 2 Error
Expand Unit 3 Error
Expand Unit 4 Error
Expand Unit 5 Error
Expand Unit 6 Error
Expand Unit 7 Error
Expand Unit 8 Error
Configuration Error B Status
CH2
CH3
CH4
Channel Error
Error Channel A Status
CH1
Expand Unit 1 Communications Error
Expand Unit 2 Communications Error
Expand Unit 3 Communications Error
Expand Unit 4 Communications Error
Expand Unit 5 Communications Error
Expand Unit 6 Communications Error
Expand Unit 7 Communications Error
Expand Unit 8 Communications Error
Internal Communications Error Status
Expand Communications Error
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
1
1
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Not used.
Bit 1
Bit 2
Bit 3
Bit 0
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
Bit 9
Bit 12
Alarm 1
Alarm 2
Alarm 3
Heater Overcurrent
HB Alarm
HS Alarm
OC Alarm
Set Point Limiter Out of Range
Set Value Limiter Reverse Operation
MV Limiter Reverse Operation
Scaling Reverse Operation
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 12
Bit 13
Bit 14
Bit 15
Bit 0
Bit 1
Bit 2
Bit 3
Bit 8
Bit 9
Channel Alarm Status
Not used.
0
1
0
1
0
0
C4/84 0000
C4/84 0001
C4/84 0002
C4/84 0003
C4/84 000B
C4/84 0004
C4/84 0101 (ch 1)
C4/84 0201 (ch 2)
C4/84 0301 (ch 3)
C4/84 0401 (ch 4)
C4/84 0102 (ch 1)
C4/84 0202 (ch 2)
C4/84 0302 (ch 3)
C4/84 0402 (ch 4)
* Error Channel A Status bits will not
turn ON even if a bit between bit 0
and bit 3 in the Channel Status is ON.
* CH2 to CH4 are the same as CH1.
Channel Status
1
0
Bits 0 to 3: Not used.
Bits 10 to 11: Not used.
Bits 13 to 15: Not used.
Bits 5 to 7: Not used.
Bits 8 to 11: Not used.
Bits 12 to 15: Not used.
Bits 8 to 11: Not used.
Bits 12 to 15: Not used.
Bits 4 to 7: Not used.
Bits 8 to 11: Not used.
Bits 12 to 15: Not used.
Bits 8 to 11: Not used.
Bits 12 to 15: Not used.
Bits 8 to 11: Not used.
Bits 4 to 7: Not used.
Bits 10 to 11: Not used.
Bits 12 to 15: Not used.
RUN/STOP
Auto/Manual
AT Execute/Cancel
SP Mode
Input Error
RSP Input Error
Bits 5 to 7: Not used.
To Next Page
Loading...
Need help?
General
