7-1-33 Electronic Thermal Load Rate Monitor [d104] ................................................... 7-16
7-1-34 Analog Voltage Input O Monitor [d130] ..............................................................7-16
7-1-35 Analog Current Input OI Monitor [d131] ............................................................ 7-16
7-1-36 Pulse Train Input EA Monitor [d133] ................................................................. 7-17
7-1-37 PID Deviation [d153]......................................................................................... 7-17
7-1-38 PID Output Monitor [d155] .................................................................................7-17
7-2
Multi-function Input/Output Functions ........................................................... 7-18
7-2-1 Multi-function Input Selection ............................................................................ 7-18
7-2-2 Multi-function Output Selection ......................................................................... 7-20
7-3
Analog I/O Settings .......................................................................................... 7-22
7-3-1 Analog Input (O, OI) .......................................................................................... 7-22
7-3-2 Analog Input Filter ............................................................................................ 7-24
7-3-3 Analog Command Hold Function (AHD) ........................................................... 7-24
7-3-4 Analog Input Adjustment ................................................................................... 7-25
7-3-5 Analog Input Start/End Function Settings ......................................................... 7-25
7-3-6 Terminal EO (Pulse/PWM Output) .................................................................... 7-27
7-3-7 Terminal AM (Analog Output)............................................................................ 7-29
7-4
Inverter Control Settings ................................................................................. 7-31
7-4-1 Carrier Frequency ............................................................................................. 7-31
7-4-2 Automatic Carrier Reduction .............................................................................. 7-32
7-4-3 2nd Control Function (SET) .............................................................................. 7-33
7-5
Other Operation Functions ............................................................................. 7-35
7-5-1 Starting Frequency ............................................................................................7-35
7-5-2 Reduced Voltage Startup Selection ...................................................................7-36
7-5-3 Frequency Jump Function ................................................................................ 7-36
7-5-4 Acceleration/Deceleration Stop Function .......................................................... 7-37
7-5-5 RUN Direction Limit Selection .......................................................................... 7-38
7-5-6 Permission of RUN Command ...........................................................................7-38
7-5-7 Frequency Calculation Function ....................................................................... 7-39
7-5-8 Frequency Addition Function ............................................................................ 7-39
7-5-9 Remote Operation Function (UP/DWN) ............................................................ 7-40
7-5-10 Output Voltage Gain .......................................................................................... 7-41
7-5-11 AVR (Automatic Voltage Regulator) Function ................................................... 7-42
7-5-12 PID Function ..................................................................................................... 7-44
7-5-13 Automatic Energy-saving Operation Function ................................................... 7-50
7-5-14 Commercial Switching (CS) .............................................................................. 7-50
7-5-15 Stabilization Parameter ......................................................................................7-52
7-5-16 Pulse Train Frequency Input ..............................................................................7-52
7-5-17 LAD Cancel Function ........................................................................................ 7-53
7-6
Digital Operator and Operation Functions .................................................... 7-54
7-6-1 Soft Lock Function (SFT) ...................................................................................7-54
7-6-2 Forced Operator Function (OPE) ......................................................................7-55
7-6-3 Forced Terminal Block Function (F-TM) ............................................................ 7-55
7-6-4 Operation Selection at External Operator Disconnection .................................. 7-56
7-6-5 Initial Screen Selection (Initial Screen after Power-on) ..................................... 7-56
7-6-6 Initial Screen Automatic Return Function .......................................................... 7-56
7-6-7 Inverter Display on Operator Connection .......................................................... 7-57
7-6-8 Display Fixed (DISP) .........................................................................................7-57
7-6-9 Password Function ........................................................................................... 7-57
7-6-10 User Parameter Setting Function...................................................................... 7-60
7-6-11 User Parameter Automatic Setting Function ..................................................... 7-60
7-6-12 Jog Dial Sensitivity............................................................................................ 7-61
7-7
Restart Functions ............................................................................................. 7-62
To Next Page
Loading...
Need help?
General
