Physio Control LIFEPAK 500

To Next Page

To Previous Page

Previous Page Table of Contents Section Contents

Back

Index Next Page

LIFEPAK 500 automated external defibrillator Parts Lists and Assembly Diagrams

12-58

Upper Case Exterior Labels and LCD Shield, 2-Button Units

Main Page

Table of Contents2
Section Contents3
Configuration Information11
Glossary12
Acronyms14
Safety15
Terms16
General Warnings and Cautions17
Symbols19
Product Description22
Physical Description and Features23
Main Components23
Monophasic and Biphasic Versions23
Options24
System Context Diagram30
Functional Description31
Operating Instructions33
Possible Improper AED Performance33
Possible Defibrillator Shutdown33
Possible Loss of Power During Patient Care33
Modes of Operation34
Normal Mode35
Setup Options36
Setting the Clock37
To Change the Date and Time37
Data Transfer Mode38
Incident Scene Review38
System Requirements38
Patient Data Management39
Transferring Setup between Aeds40
User Test Mode41
Auto Test Modes42
Power-On Self-Test42
Auto Tests43
Daily Auto Test44
Extended Auto Test45
Auto Battery Test Mode46
Service Mode49
To Place the LIFEPAK 500 AED in Service Mode50
Automatic Tests56
Clear Fault Codes57
To Clear Fault Codes from the Fault Code Log57
Performance Inspection58
Troubleshooting59
Fault Codes60
Corrective Action Codes61
Fault Code Table62
Troubleshooting Chart83
Preventive Maintenance90
Preventive Maintenance and Testing Schedule91
Introduction91
Guidelines91
Product Useful Life92
Product Support Policy93
Battery Maintenance94
Rechargeable Battery Pak95
Nonrechargeable Battery Pak97
Recharging a Rechargeable Battery Pak99
Receiving New Batteries101
Battery Storage102
Discharging Nonrechargeable Batteries103
Recycling Rechargeable Batteries105
Assessing Batteries106
AED Cleaning108
External Cleaning Procedures108
Internal Cleaning Procedures109
AED Storage110
Replacement111
Replacement Procedures for LIFEPAK 500 Monophasic AED112
Warnings and Cautions115
Electrostatic-Sensitive Device Handling116
Look for SSD Symbol116
Wear a Wrist Strap117
Test Work Area Often117
Discharging Energy Storage Capacitor118
Building a Capacitor Discharge Tool119
LIFEPAK 500 AED Discharge Tool Parts119
Recording User-Defined Setups120
Replacing Case127
Application127
Preparation127
Preparing Top Cover for Replacement130
Removing Top Cover131
Reassembling Case133
Replacing Readiness Display—Biphasic AED135
Replacing Keypad Overlay136
To Replace the Keypad Overlay136
Replacing Time-Of-Day Clock Battery137
Replacing a Main PCB Switch Cap139
Setting Aside Main PCB140
Reseating Main PCB143
Removing Main Pcb—Monophasic AED145
Removing Main Pcb—Biphasic AED152
Replacing Battery Plate Wire Harness164
Removing Energy Storage Capacitor—Biphasic AED170
Replacing Speaker Assembly172
Replacing Wave Shaping Inductor—Monophasic AED175
To Install the New Wave Shaping Inductor176
Replacing Patient Connector Harness—Monophasic AED179
Replacing Patient Connector Harness—Biphasic AED183
Operating System Software188
Parts Lists189
Product Configuration189
Parts Configurator191
Waveform Type?191
Analyze-Button Unit?192
Service Kits194
LIFEPAK 500 AED Assembly Diagrams244
Upper Case Exterior Labels and LCD Shield, 3-Button Units245
Main PCB and Attaching Hardware248
Lower Case Interior Components—Monophasic AED249
Lower Case Interior Components—Biphasic PCB250
Wire Routing and Tie-Wrap Placement—Monophasic AED251
Wire Routing and Tie-Wrap Placement—Biphasic AED252
LIFEPAK 500 AED Interconnection Diagram—Monophasic AED253
LIFEPAK 500 AED Interconnection Diagram—Biphasic AED254
Index255

Physio Control LIFEPAK 500 - Page 246

Table of Contents

Related product manuals