Sharp AQUOS LX959H - Reset; Downloading the software; Download setup

96
Appendix
Ifcomplexadjustmentsaremadeandthesettings
cannot be restored to normal, you can reset the
settingstothefactorypresetvalues.
Press
a
/
b
toselect“Reset”,andthenpress
?
.
3
Press
c
/
d
toselect“Yes”,andthenpress
?
.
• “Now,TVwillrestartautomatically.OK?”displays
on the screen.
5
Press
MENU
andtheMENUscreendisplays.
1
Press
c
/
d
toselect“Yes”,andthenpress
?
.
• “Nowinitialising...”displaysonthescreenand
blinks.
• Aftertheresethascompleted,thepowershuts
offandthencomesbackon.Thescreenwillhave
returned to its original settings.
6
Reset
Ifyouhavealreadysetthepassword,enterit
here.
• “Returntofactorypre-settings”displaysonthe
screen.
4
Information
Press
a
/
b
to select the desired language
listed on the screen, and then press
?
.
Press
c
/
d
toselect“HOME”or“STORE”,
and then press
?
.
7
8
Press
c
/
d
toselect“DigitalSearch”or
“AnalogueSearch”,andthenpress
?
.
9
TheTVsearchesfor,sortsandstoresall
thereceivableTVstationsaccordingtotheir
settings and the connected antenna.
•Toaborttheinitialautoinstallationinprogress,press
RETURN
.
NOTE
• WhentheTVisin“STORE”mode,repeatsteps1to7tochangeto
“HOME”mode.
• “Reset”isgreyedoutin3Dmode.Toselectthe“Reset”menu,you
need to switch to 2D mode.
Download setup
TheTVautomaticallydetermineswhetheranewsoftware
versionisavailablewhentheTVisinstandbymode.
Goto“Menu”
s
“Setup”
s
“Viewsetting”
s
“Individual
setting”
s
“Standbysearch”
s
“Download setup”.
Selected item Description
Yes
Automatically searches for new software
updatesavailablewhentheTVisin
standby mode.
No Does not search for update information.
Now
Checksifthereisnewsoftware
immediately.
Downloading the software
Youcanselectthemethodofupdate.
Selected item Description
Yes
Startsdownloadingimmediately.
Typically, it takes approximately 30
minutesfordownload.Youcannotcarry
out other operations while downloading.
• Cancelsthedownloadbypressing
?
on
the remote control unit when “Discontinue”
is displayed on the screen during the
update.
No
Startsdownloadingautomaticallyseveral
minutes after entering standby mode.
NOTE
• Updatingthesoftwaremaytakeseveralhoursintheworstcase.
• TheTVmustremaininstandbymodefordownload.Donotturnoff
the power.
Pressb/
c
/
d
toselect“Viewsetting”.
2
Now initialising...
After factory presetting,
TV will restart automatically
Ifthesoftwareisupdated,theconrmation
message “New download information has
been detected.” appears.
• IftheTVreceivestheupdateservicewhilein
standbymode,aconrmationmessagedisplays
after turning on the power.
1
Followthescreenprompts.
2
Picture / Audio test
WhenexternalequipmentisconnectedwiththeTV
poweredonandthereisnoaudio/videooutput,the
TVmaydeterminewhichequipmentcouldcausea
problembetweentheTVandtheexternalequipment.
Goto“Menu”>“Setup”>“Information”
>“Picture/Audiotest”.
NOTE
• Terminalswhichcanbetested:
HDMI,component,composite,D-sub
• Externalspeakerscannotbetested.Thisfunctionisavailableforthe
TVspeakersonly.
Selected item Description
Picture test
Performatestforpicturedisplay.When
external equipment is connected but the
picture is not displayed, the test will be
performed.
Audio test
Performatestforaudioplayback.When
external equipment is connected but the
audio does not playback, the test will be
performed.