MX-3114N SIMULATION 6 – 92
A-I: When the adjustment value is increased, the image loss is increased.
1step = 0.1mm
50-28
Purpose
Adjustment
Function (Purpose)
Used to automatically adjust the image
loss, void area, image off-center, and image
magnification ratio.
Section
Operation/Procedure
The following adjustment items can be executed automatically with
SIM50-28.
* ADJ16 Print image position, image magnification ratio, void area,
off-center adjustments (Manual adjustments)
* ADJ 17 Scan image magnification ratio adjustment (Manual
adjustment)
* ADJ 18 Scan image off-center adjustment (Manual adjustment)
* ADJ 19 Used to adjust the copy image position and the image
loss (Manual adjustments)
1) Select an adjustment item with the menu button.
2) Press [EXECUTE] key, and the adjustment pattern is printed.
3) Set the adjustment pattern on the document table.
4) Press [EXECUTE] key, and the adjustment pattern is scanned.
5) Press [OK] key.
Image send mode
(Except for FAX and
copy)
A Image loss
amount setting OC
LEAD_EDGE (OC) OC lead edge image loss amount setting 0 - 100 0 (0mm)
B FRONT_REAR(OC) OC side image loss amount setting 0 - 100 0 (0mm)
C TRAIL_EDGE(OC) OC rear edge image loss amount setting 0 - 100 0 (0mm)
D Image loss
amount setting
SPF SIDE1
LEAD_EDGE (SPF_SIDE1) Front surface lead edge image loss
amount setting
0 - 100 0 (0mm)
E FRONT_REAR (SPF_SIDE1) Front surface side image loss amount
setting
0 - 100 0 (0mm)
F TRAIL_EDGE(SPF_SIDE1) Front surface rear edge image loss
amount setting
0 - 100 0 (0mm)
G Image loss
amount setting
SPF SIDE2
LEAD_EDGE (SPF_SIDE2) Back surface lead edge image loss
amount setting
0 - 100 0 (0mm)
H FRONT_REAR (SPF_SIDE2) Back surface side image loss amount
setting
0 - 100 0 (0mm)
I TRAIL_EDGE(SPF_SIDE2) Back surface rear edge image loss
amount setting
0 - 100 0 (0mm)
Item/Display Content Setting range Default value
Item/Display Content Section
OC ADJ MFT Document lead
edge
Document off-
center
Sub scanning
magnification ratio
Image loss off-
center sub scanning
direction image
magnification ratio
adjustment
(Document table
mode)
Scanner
CS1
CS2
ADU
CS3
CS4
LCC
Item/Display Content Section
SPF
ADJ
(RSPF)
ALL SIDE1
(Front
surface)
MFT Document
lead edge
Document
off-center
Sub
scanning
magnifica-
tion ratio
Document
lead edge
Document
off-center
Sub
scanning
magnifica-
tion ratio
Image loss
off-center
sub
scanning
direction
image
magnifica-
tion ratio
adjustment
(RSPF
mode)
Scanner
SIDE2
(Back
surface)
CS1
CS2
ADU
CS3
CS4
LCC
Item/Display Content Section
SETUP/
PRINT
ADJ
ALL LEAD MFT Print off
center
Print lead
edge
Print lead
edge
adjustment,
image off-
center
(each paper
feed tray,
duplex
mode)
adjustment
Engine
CS1
CS2
OFFSET ADU
CS3
CS4
LCC
Item/Display Content Section
BK-MAG
ADJ
MFT BK main scanning
magnification ratio
Main scanning
direction image
magnification ratio
adjustment
Engine
CS1
CS2
ADU
CS3
CS4
LCC
RESULT Adjustment result display
DATA Adjustment operation data display
To Next Page
Loading...
