Sharp MX-2314N - Page 57

MX-3114N ADJUSTMENTS AND SETTINGS 5 – 8
2-C Transfer current and voltage adjustment
This adjustment must be performed in the following cases:
* When the TC high voltage PWB is replaced.
* U2 trouble has occurred.
* The PCU PWB has been replaced.
* The EEPROM of the PCU PWB has been replaced.
1) Enter the SIM 8-6 mode.
2) Select an item to be adjusted.
EXECUTE
EXECUTE
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
7+96(77,1*$1'287387



$˖
˷˹
˖7&/2:63(('&/.
$˖ 
˖7&0,''/(63(('&/.%˖ 
˖7&/2:63(('&/&&˖ 
˖7&0,''/(63(('&/&
'˖ 
˖7&0,''/(63(('&/0)˖ 
˖7&/2:63(('&/0
(˖ 
˖7&/2:63(('&/<*˖ 
˖7&0,''/(63(('&/<
+˖ 
˖7&/2:63(('%:.,˖ 
˖7&0,''/(63(('%:.-˖ 
˖7&3/$,1&/63;
.˖ 
˖7&3/$,1&/'3;
/˖ 
2.
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
7+96(77,1*$1'287387



$˖
˷˹
˖7&/2:63(('&/.
$˖ 
˖7&0,''/(63(('&/.%˖ 
˖7&/2:63(('&/&&˖ 
˖7&0,''/(63(('&/&'˖ 
˖7&0,''/(63(('&/0)˖ 
˖7&/2:63(('&/0(˖ 
˖7&/2:63(('&/<*˖ 
˖7&0,''/(63(('&/<+˖ 
˖7&/2:63(('%:.,˖ 
˖7&0,''/(63(('%:.
-˖ 
˖7&3/$,1&/63;
.˖ 
˖7&3/$,1&/'3;
/˖ 
2.
(;(&87(
or after 30 sec.
10-key
Item/Display Content Setting
value
Default value
23cpm 26cpm/31cpm
A TC1 LOW SPEED CL K
Primary transfer
bias adjustment
value
Color
K
Low speed 51 - 255 80 80
B TC1 MIDDLE SPEED CL K Middle speed 51 - 255 95 109
C TC1 LOW SPEED CL C
C
Low speed 51 - 255 80 80
D TC1 MIDDLE SPEED CL C Middle speed 51 - 255 95 109
E TC1 LOW SPEED CL M
M
Low speed 51 - 255 80 80
F TC1 MIDDLE SPEED CL M Middle speed 51 - 255 95 109
G TC1 LOW SPEED CL Y
Y
Low speed 51 - 255 80 80
H TC1 MIDDLE SPEED CL Y Middle speed 51 - 255 95 109
I TC1 LOW SPEED BW K
Black/
White
K
Low speed 51 - 255 80 80
J TC1 MIDDLE SPEED BW K Middle speed 51 - 255 95 109
K TC2 PLAIN CL SPX
Secondary transfer
bias adjustment
value
Color
Plain
paper
Front surface 51 - 255 96 103
L TC2 PLAIN CL DPX Back surface 51 - 255 76 90
M TC2 PLAIN BW SPX
Black/
White
Front surface 51 - 255 96 103
N TC2 PLAIN BW DPX Back surface 51 - 255 76 90
O TC2 HEAVY CL SPX
Color
Heavy
paper
Front surface 51 - 255 83 83
P TC2 HEAVY CL DPX Back surface 51 - 255 76 76
Q TC2 HEAVY BW SPX
Black/
White
Front surface 51 - 255 69 69
R TC2 HEAVY BW DPX Back surface 51 - 255 69 69
S TC2 HEAVY2 CL Color
Heavy paper 2
51 - 255 83 83
T TC2 HEAVY2 BW
Black/
White
51 - 255 69 69
UTC2 HEAVY3 CL Color
Heavy paper 3
51 - 255 83 83
V TC2 HEAVY3 BW
Black/
White
51 - 255 69 69
W TC2 OHP CL Color
OHP
51 - 255 69 69
X TC2 OHP BW
Black/
White
51 - 255 69 69
Y TC2 ENVELOPE CL Color
Envelope
51 - 255 69 69
Z TC2 ENVELOPE BW
Black/
White
51 - 255 69 69
AA TC2 THIN CL Color
Thin paper
51 - 255 96 103
AB TC2 THIN BW
Black/
White
51 - 255 96 103
AC TC2 GLOSSY CL Color
Gloss paper
51 - 255 83 83
AD TC2 GLOSSY BW
Black/
White
51 - 255 69 69
AE TC2 CLEANING
Secondary transfer
cleaning bias
adj
ustment value
Cleanig process (negative pole) 51 - 255 59 59
AF TC2 CLEAN LOW SPD Low speed print mode 0 - 255 26 26
AG TC2 CLEAN MIDDLE SPD Middle apeed print mode 0 - 255 26 26
AH TC2 CLEAN CLEANING Cleaning bias (positive pole) 0 - 255 102 102
AI PTC LOW SPEED CL
PTC current
adjustment value
Color
Low speed 51 - 255 73 73
AJ PTC MIDDLE SPEED CL Middle apeed 51 - 255 73 73
AK PTC LOW SPEED BW
Black/
White
Low speed 51 - 255 73 73
AL PTC MIDDLE SPEED BW Middle apeed 51 - 255 73 73
AM CASE VOLT LOW CL
PTC voltage
adjustment value
Color
Low speed 0 - 255 0 0
AN CASE VOLT MID CL Middle apeed 0 - 255 0 0
AO CASE VOLT LOW BW
Black/
White
Low speed 0 - 255 0 0
AP CASE VOLT MID BW Middle apeed 0 - 255 0 0