Parameter Description
(9) Distribution and control of the external terminal’s function
5.23Multi-function Output (P.40, P.85, P.120, P.129, P.130) ...................................................................... 102
5.24 Up-to-frequency Sensitivity (P.41) .................................................................................................... 104
5.25 Output Frequency Detection (P.42 and P.43) .................................................................................... 104
5.26 AM1/HDO Terminal (P.54~P.56, P.64, P.74, P.187, P.190 and P.191) ................................................ 105
5.27 AM2 Terminal (P.535 ~ P.538) .......................................................................................................... 109
5.31 Zero Current Detection (P.62 and P.63) ............................................................................................ 113
5.39 Multi-function Terminal Function Selection (P.80~P.84, P.86, P.126, P.550) ....................................... 120
5.50 External Terminals Filter Adjusting Function (P.157) ......................................................................... 135
5.83 HDI terminal input signal (P.522~P.526) ........................................................................................... 178
(10) The monitor display and output signal
5.12 Output Frequency Filter Constant (P.28) ............................................................................................ 69
5.18 Speed Display (P.37, P.259) ............................................................................................................... 95
5.46 Operation Panel Monitoring Selection (P.110) .................................................................................. 132
5.53 Multi-Function Display (P.161) ......................................................................................................... 137
(11) The motion selection when the power cuts out in the moment
5.28 Restart Function (P.57, P.58, P.150 and P.160)................................................................................. 109
(12) The motion setting when something unusual happened
5.32 Retry Function (P.65, P.67, P.68, P.69) ............................................................................................. 114
5.55 4-5 Terminal Disconnection Handling Function (P.184) ..................................................................... 144
5.72 Vibration Inhibition Factor (P.285 and P.286) .................................................................................... 165
5.73 Short Circuit Protection Function (P.287) .......................................................................................... 166
(13) Running with energy saving
5.52 Energy-Saving Control Function (P.159) .......................................................................................... 136
(14) The noise reducing of motor and electromagnetism
5.15 Carrier Operation Selection(P.31) V/F.............................................................................................. 74
5.34 Carrier Frequency (P.72).................................................................................................................. 116
(15) The setting of analog input frequency and torque (terminal 2 and 4)
5.19 Function Selection of HDI Terminal and Analog Terminal (P.500, P.501, P.502, P.503) ........................ 96
5.20 The Voltage Signal Selection across Terminal 2-5 and Target Frequency (P.38, P.73) ......................... 97
5.21 The Input Signal Selection across Terminal 4-5 and the Target Frequency (P.17, P.39) ....................... 99
5.22 The Voltage Signal Selection across Terminal 1-5 and the Target Frequency(P.509, P.530) .............. 101
5.29 Input Signal Filter Constant (P.60, P.528, P.529)............................................................................... 111
5.56 The Proportion Linkage Function and The Auxiliary Frequency Function (P.185, P.240).................... 144
5.60 2-5 Terminal Input Signal (P.139, P.192~P.195, P.510~P.513) ........................................................... 147
5.61 4-5 Terminal Input Signal (P.196~P.199, P.505) ................................................................................ 153
5.62 1-5 Terminal Input Signal (P.506，P.514~P.521) .............................................................................. 154
(16) Misoperation preventation and frequency setting limit
5.35 Stop or Reset Function Selection (P.75) ........................................................................................... 118
5.36 Parameters Write Protection (P.77) .................................................................................................. 118
5.37 Forward/Reverse Rotation Prevention Selection (P.78) .................................................................... 119
5.59 Factory Setting Function (P.189) ...................................................................................................... 146
To Next Page
Loading...
Need help?
General
