To Next PageTo Next Page
Need help?Do you have a question about the Siemens PROFINET SIRIUS 3RW5 and is the answer not in the manual?
General| Brand | Siemens |
|---|---|
| Model | PROFINET SIRIUS 3RW5 |
| Category | Controller |
| Language | English |
Online form to send questions directly to technical support.
Links to further manuals and online helps for automation systems.
Personal work area for managing requests, filters, favorites, notifications, products, and documentation.
Information on industrial security functions for secure operation of plants, systems, machines and networks.
Requirements, threats, and precautions for data security in industrial environments.
Guidelines for handling electrostatic sensitive components and devices to prevent damage.
Information on EMC design and potential radio interference in domestic environments.
Guidance on environmentally friendly recycling and disposal of old electrical and electronic devices.
Overview of manual revisions and new features released across different versions.
Details on the article numbers and hardware layout of the 3RW5 PROFINET communication modules.
Overview of PROFINET IO characteristics and supported functions for the communication module.
Details on how to access the soft starters via different paths like PROFINET, web client, or HMI.
Explanation of different operating modes and how master control is managed between sources.
Step-by-step guide for mounting the communication module into the soft starter's slot.
Procedure for safely removing the slot cover from the soft starter before module installation.
Instructions for physically installing the communication module into the prepared slot.
Procedure for safely removing the communication module from its slot in the soft starter.
Instructions for mounting the communication module directly onto a flat surface.
Procedure for safely removing the communication module that is mounted on a level surface.
Information about the COM connecting cable used for communication between devices.
Step-by-step instructions for connecting the COM cable to the 3RW50 soft starter.
Guide for connecting the COM connecting cable to the communication module.
Procedure for disconnecting the COM connecting cable from the communication module.
Instructions for disconnecting the COM connecting cable from the 3RW50 soft starter.
Details on connecting to the fieldbus for industrial communication.
Procedure for connecting the fieldbus connector to the communication module.
Steps for configuring the 3RW5 Soft Starter within a PROFINET IO system.
General procedures for configuring the 3RW5 Soft Starter, including via HMI or without.
Configuration steps via controller software without using a 3RW5 HMI High Feature.
Information on selecting and setting the device name for PROFINET communication.
Details on setting IP addresses, subnet masks, and router addresses for PROFINET devices.
Methods for integrating the soft starter into the PROFINET IO system using HSP or GSDML files.
Defines behavior of the soft starter upon bus connection failure or CPU stop in 'Automatic' mode.
Explanation of the diagnostic LEDs on the 3RW5 PROFINET communication modules.
How the controller software provides diagnostics and handles interrupts from the soft starter.
Information on using data sets for diagnostics, including communication module, soft starter, and HMI diagnostics.
List and causes of error codes received for negative data set acknowledgements.
Configuration options to enable or disable the transmission of error and maintenance interrupts.
Table of possible errors and their remedies for the communication module.
Description of message bits in data set 92 indicating which control source has priority.
Vendor-neutral profile for energy management, supporting commands for energy saving and measured values.
Procedure for synchronizing the real-time clock using the Network Time Protocol.
Functionality to retrieve information and control soft starters via web pages using a web browser.
Details on using the OPC UA server for data exchange between clients and systems.
Parameter determining soft starter behavior relative to a PLC, relevant for web server or OPC UA server use.
Enables setup of system-redundant plants for high availability automation systems.
Ability to make system changes without restarting devices or controllers, also known as Configuration in Run (CiR).
Instructions and information on updating the firmware to extend functions and improve security.
Step-by-step guide for updating firmware using a micro SD card via the 3RW5 HMI High Feature.
Procedure for replacing the communication module, noting that communication parameters are not automatically transferred.
How to reset the soft starter, communication module, and HMI to their factory default settings.
Information on how to find technical data sheets and overview tables on the Siemens Industry Online Support portal.
Information on accessing CAx data (CAD drawings, etc.) for devices via Siemens Industry Online Support.
Detailed drilling patterns for mounting the 3RW5 communication module on 3RW50 soft starter sizes S6 and S12.
Information on accessing CAx data, which includes circuit diagrams, via Siemens Industry Online Support.
Overview of the appendix structure and content, referencing Equipment Manuals for more details.
Explanation of data formats, including current values as percentages and bit arrangements.
Description of statistic data grouping operating states for load relevance and preventive diagnostics.
Information on stored extreme measured values used for preventive diagnostics, which can be deleted.
Details on how the 3RW5 soft starter's functions are controlled and monitored via process data and images.
Comprehensive list of available data sets for communication module, soft starter, HMI, and I&M data.
