Siemens SIREMOBIL Iso-C

To Next Page

To Previous Page

SIREMOBIL Iso-C SPR2-230.061.01 Page 18 of 18 Siemens AG

System Manual Rev. 13 12.04 CS PS 24 Medical Solutions

1 - 18 Prerequisites

Concluding steps 1

After completing all work, perform the protective conductor test (refer to

ARTD-002.731.17).

Main Page

Table of Contents3
Required Documents9
Required Tools, Measurement and Auxiliary Devices9
Information Regarding this Document10
Position Designations10
Safety Information11
Notes on the Protective Conductor Resistance Test15
Notes on Device Leakage Current Measurement16
Basic System19
Removing the Cover19
Installing the Cover19
Cover over the Horizontal Carriage20
Removing the Cover20
Attaching the Cover21
SIREPHOS Cover22
Monitor Trolley23
Removing the Covers23
Installing the Covers24
Installing/Removing the Cover at the C-Arm Mounting24
Telescoping Cover Underneath the Horizontal Carriage24
I.I. Service Position25
Moving the I.I. into the Service Position25
Installing the I.I25
Concluding Steps26
Checking the Line Voltage on the Monitor Trolley27
Low Voltages29
I.I. Voltages29
Control Board D1, Host31
Storage of the Error Log as ASCII File31
Option 3D Reconstruction, Trace File and Event Log File32
Saving Trace Files32
Saving Current Trace Files Directly after Display of an Error33
Checking the Generator Adjustment39
Dose Rate Adjustment41
Prerequisites41
Preliminary Steps41
Correction Factors41
Setting the Dose Rate for Survey Format42
Setting the Dose Rate for Zoom Format43
Concluding Steps44
Checking the Dose Rate in Automatic Mode44
Setting the Maximum Skin Dose Rate45
Prerequisites45
Preparations45
Measurement45
Programming46
Checking46
Collimator, X-Iris47
Collimator, Slot Diaphragm48
Prerequisites48
Adjustment48
Concluding Steps50
Collimator Displays on the Monitor50
Prerequisites50
Collimator Display, X-Iris50
Start Adjustment50
Full Format, X-Iris Open50
Full Format, X-Iris Closed51
Zoom Format, X-Iris Closed51
Zoom Format, X-Iris Open51
Save Values and End Adjustment52
Concluding Tasks52
Slot Diaphragm52
Start Adjustment52
Full Format, Slot Diaphragm Open52
Full Format, Slot Diaphragm Closed53
Zoom Format, Slot Diaphragm Closed53
Enable Circle Mask53
Save Values and End Adjustment54
Concluding Tasks54
Correction of the 0° Position of the Slot Diaphragm Display54
Camera Rotation55
Calibrating the Area Dose Product Measurement Device57
CONSTANT Parameter (Qt * Kg) = T57
Programming57
Checking the Programmed Values58
Checking the Accuracy of the Area Dose Product Measurement Device59
Prerequisites59
Preparations59
Dose Measurement60
Calculating the Area Dose Product60
Evaluation61
Overview of SIREMOBIL Iso-C Parameters62
Overview of MEMOSKOP C / C-E / C-SUB / C & MOD / C-SUB & MOD Parameters62
Configuring the MEMOSKOP65
MEMOSKOP C-E, Keyboard Emulation65
Configuring the Video Frequency65
MEMOSKOP, Configuration for the Number of Existing Monitors66
MEMOSKOP, Configuration and Country-Specific Language (User Setup)66
Control Board D167
Replacement and Additional Work67
Power Board D268
Interface Board D3068
Replacing the VIDEOMED DC69
Camera Rotation 0° Position69
Checks and Adjustments70
Basic System Operating Panel70
Frequency Converter FU (Vertical Lift)71
Power Supply M14, +5 V / +15 V / -15 V72
Power Supply M13, +13 V VIDEOMED DC72
I.I. Mini Voltage Supply73
Collimator76
Sirephos77
Replacing the I.I78
Checking the Temperature Indicator78
Removal79
Videomed DC79
I.I. Mini Voltage Supply79
And Compact Optics80
Installation80
Compact Optics80
Mini Voltage Supply81
Videomed DC81
Miscellaneous Parts81
Checks and Adjustments81
Concluding Work82
Replacing the Compact Optics83
Camera Optics83
Videomed DC84
High Voltage Section of the I.I. Mini Voltage Supply84
Compact Optics84
Installation85
Optics85
High Voltage Section86
Camera Rotation 0° Position86
Siemens AG86
Spr2-230.061.0186
Videomed DC86
Miscellaneous Cables86
Settings86
Resolution86
Dose Rate87
Checking the Camera Optics Centering at the I.I. Output87
Centering the Camera Optics to the I.I. Output88
Checks and Adjustments89
Memoskop C-E 10090
Memoskop C / Memoskop C & Mod95
Memoskop C-Sub / Memoskop C-Sub & Mod97
Multispot 2000100
Area Dose Product Meter100
Laser Targeting Device100
Mouse, External Mouse and PC Keyboard101
Replacing the Mouse101
Replacing the External Mouse101
Replacing the PC Keyboard101
Video Switcher102
SIMOMED HM Monitor105
3D Reconstruction System Electronics105
Orbital Motor106
Orbital Drive Toothed Belt108
Orbital Drive Actual Value Potentiometer110
Setting the Actual Value Potentiometer for C-Arm Orbital Movement111
Belt of the Actual Value Potentiometer for Orbital Movement112
Setting the Actual Value Potentiometer for C-Arm Orbital Movement112
Angulation Part113
Brake Force / Brake Torque115
Measuring the Horizontal Force Required for Movement115
Measuring the Horizontal Swivel Force115
Measuring the Orbital Force Required for Movement116
Measuring the Angular Force Required for Movement116
Horizontal Swivel Brake118
Vertical Lift Motor120
Vertical Lift Limit Switches121
Switch for Blocking Vertical Lift121
Emergency off Switch122
Lubricating the Lifting Column122
Spindle122
Guide Cylinder122
Tensioning the Drive Belt123

Table of Contents

Other manuals for Siemens SIREMOBIL Iso-C

Related product manuals