To Next PageTo Next Page
Need help?Do you have a question about the Siemens SIREMOBIL Iso-C and is the answer not in the manual?
General| Brand | Siemens |
|---|---|
| Model | SIREMOBIL Iso-C |
| Category | Medical Equipment |
| Language | English |
Information about copyright ownership.
Details on manual version and updates.
Legal disclaimer regarding documentation use.
Lists necessary documentation for the procedure.
Lists essential tools and equipment for service.
Guidance on using the service instructions.
Explains directional terms used in the manual.
Explains meaning of symbols and emphasized text.
Crucial safety warnings and precautions.
Warnings about potential biological hazards.
Safety instructions regarding X-ray exposure.
Warnings about hazards from mechanical components.
Precautions against ESD damage.
Warning about hot components.
Warnings about injury during disassembly/assembly.
Guidance on performing protective conductor tests.
Instructions for measuring device leakage current.
Procedures for removing/installing covers.
Steps for removing and installing the SIREPHOS cover.
Procedures for C-arm cover removal and installation.
Instructions for removing and installing monitor trolley covers.
Steps to move the I.I. into the service position.
Procedures for installing the I.I. component.
Final steps after performing work.
How to check line voltage on the monitor trolley.
Procedures for checking low voltage levels.
How to check Image Intensifier voltages.
Steps for loading software onto control board D1.
How to save the error log in ASCII format.
Procedures for saving trace files.
Saving trace files after an error occurs.
Steps to save Event-Log files.
How to adjust the generator's kV offset.
Performing generator adjustment via learning program.
Verifying the generator adjustment settings.
Procedure for adjusting the dose rate.
Procedures to reduce maximum air kerma rate.
Adjusting the X-Iris collimator.
Adjusting the slot diaphragm.
Procedures for adjusting camera rotation.
Calibration and programming for PTW dose-area device.
Programming and testing WELLHÖFER dose-area device.
Verifying accuracy of dose-area product measurement.
Overview of available SIREMOBIL Iso-C parameters.
Overview of MEMOSKOP parameters.
Configuration steps for MEMOSKOP.
Configuring language and user setup for MEMOSKOP.
Steps for replacing the D1 control board.
Procedures for replacing the D2 power board.
Steps for replacing the D30 interface board.
Procedures for replacing the VIDEOMED DC.
Procedures for replacing the basic system operating panel.
Steps for replacing the frequency converter.
Replacing the M14 power supply.
Replacing the M13 power supply.
Procedures for replacing the I.I. mini-voltage supply.
How to adjust the I.I. mini-voltage supply.
Procedures for replacing the collimator.
Procedures for replacing the SIREPHOS.
Steps for replacing the Image Intensifier.
Procedures for replacing Compact optics.
Configuration of MEMOSKOP C-E.
Configuration of MEMOSKOP C-E 100.
Configuration of MEMOSKOP C/C & MOD.
Configuration of MEMOSKOP C-SUB/C-SUB & MOD.
Installation and configuration of MULTISPOT 2000.
Procedures for replacing dose-area product devices.
Procedures for replacing the laser targeting device.
Procedures for replacing input devices.
Procedures for replacing the video switcher.
Replacing PC board D210 for cut-off delay.
Procedures for replacing the 3D reconstruction PC.
Procedures for replacing the SIMOMED HM monitor.
Replacing 3D reconstruction system electronics.
Procedures for replacing the orbital motor.
Procedures for replacing the toothed belt.
Procedures for replacing the actual value potentiometer.
Procedures for replacing the angulation part.
Measuring brake force and torque.
Measuring horizontal force for movement.
Measuring horizontal swivel force.
Measuring orbital force for movement.
Measuring angular force for movement.
Replacing the angulation brake magnet.
Replacing the horizontal swivel brake.
Procedures for replacing the vertical lift brake.
Procedures for replacing the vertical lift motor.
Replacing vertical lift limit switches.
Replacing switch for blocking vertical lift.
Replacing the emergency off switch.
Lubrication procedures for the lifting column.
Procedure for tensioning the drive belt.
