Applicable Models
PFV-D10 Digital Video Interface Unit
PFV-D300 Digital Video Interface Unit
PFV-D50A Digital Video Interface Unit
Specifications
Inputs/outputs
Serial digital input:
SDI IN connector (BNC type) (1)
0.8 Vp-p, 75 Ω
NTSC composite serial digital signal
conforming to SMPTE259M-A, 143 Mb/s
Cable length:
200 m max. (When using a Belden
8281, Fujikura 5C2V or equivalent
coaxial cable)
Serial digital outputs:
Active through-out connector (BNC
type) (1)
0.8 Vp-p610%, 75 Ω
Serial digital video signal of the same
format as that to the input connector
SDI OUT connectors (BNC type) (4)
0.8 Vp-p610%, 75 Ω
525-line component serial digital signal
conforming to SMPTE259M-C (ITU-R
BT.601/BT.656), 270 Mb/s
Reference video input:
REF IN connector (BNC type) (1)
Reference video output:
Loop-through output connector (BNC
type) (1)
System delay:
Approx. 70.5 µs
(in INPUT mode, with SYSTEM
H-PHASE “00”)
Output phase adjustable range:
Coarse adjustment: -4.74 µs to +4.70 µs
(-128 CK to +127 CK)
in INPUT mode: 0 to +9.44 µs (0 to
+255 CK)
(1 CK: approx. 37 nsec)
Video characteristics
Band width:
6 MHz
K factor:
Less than 1%
Signal-to-noise ratio:
More than 58 dB DG (10 kHz to video
fg.)
General
Power requirements:
+5 V DC: 1400 mA, -5 V DC: 600 mA
(supplied from the PFV-D/PFV-HD Series
Interface Unit)
Power consumption:
10 W
Operating temperature:
5 to 40 °C (41 to 104 °F)
Storage temperature:
-20 to 60 °C (-4 to 140 °F)
Operating humidity:
10 to 90% (no condensation)
Dimensions
Board (H x W):
195 x 310 mm
(7 3/4 x 12 1/4 inches)
Connector panel (H x W):
195 x 25 mm
(7 3/4 x 1 inches)
Mass
Board:
Approx. 650 g (1 lb 7 oz)
Connector panel:
Approx. 200 g (7 oz)
DEC
CLK
ACTIVE
LOOP-THROUGH
REF IN
LOOP-THROUGH
1
2
3
4
NTSC COMPOSITE
SERIAL DIGITAL
VIDEO INPUT
525-LINE COMPONENT
SERIAL DIGITAL
VIDEO OUTPUT
The BKPF-021 converts an NTSC composite serial digital
video signal to a 525-line component serial digital video
signal with 10-bit resolution. A frame synchronizing
function synchronizes the output video signal to either an
external reference signal or the input signal.
Features
* Converts an NTSC composite serial digital video signal
to a 525-line component serial digital video signal * Phase
adjustment of output signal * Set-up remove function *
Auto-freeze function * Selection of Y/C separation point *
Supports ISR * Supports EDH
The BKPF Series function boards install in both the PFV-D and the PFV-HD
Series Interface Units. In a PFV-HD Series Interface Unit, they can be
installed together with the HKPF Series function boards.
BKPF-021 NTSC Composite Digital to 525-Line Component Digital
Video Converter Board
Rear Panel
123
Interface Processor D Series
Interface Processor D Series
*SGC_0117-0132 02.3.16 5:06 PM Page 123
To Next Page
Loading...
