Steris V-PRO maX 2

To Next Page

To Previous Page

6 — Operation

10085896_H

V-PRO

maX 2

Operator Manual

(Refer to LEAK TEST)

(Refer to V

ACUUM PUMP MAINTENANCE

INDICATOR)

(Refer to S

TERILANT CUP INSTALLATION AND REMOVAL)

Main Page

Table of Contents9
Safety Precautions12
Introduction12
DANGER - Slipping Hazard13
DANGER - Fire and Explosion Hazard13
DANGER - Personal Injury, Contaminated Load And/Or Equipment Damage14
DANGER - Chemical Injury Hazard14
WARNING - Personal Injury And/Or Equipment Damage Hazard15
Warning Biohazard Control16
WARNING - Electric Shock Hazard16
WARNING - Aborted Cycle Hazard16
WARNING - Slipping Hazard17
CAUTION - Possible Equipment Damage17
Glossary and Symbols19
Glossary19
Hydrogen Peroxide Sterilization20
Symbols23
Installation Verification26
Introduction26
Installation Checklist26
Technical Specifications28
Hydrogen Peroxide Handling31
Hydrogen Peroxide Handling Precautions31
Sterilant Cup Installation and Removal32
Component Identification37
General37
Main Sterilization Unit and Cycle Controls37
Control Displays (Touch Screens)39
Alarm Screens40
Thermal Printer42
Printouts42
Operation43
Introduction43
Advisory43
Preliminary Information43
Before Operating Sterilization Unit44
Load Sterilization Unit46
VHP Sterilization Cycle Operation48
Troubleshooting60
Introduction60
Typical Alarm Screen61
Typical Alarm Printout62
Alarm Types63
Air Utility Failure - ALM64
Biological Indicator Issue - Nonalm64
Chamber Overtemp - ALM65
Chamber Pressure Deviation - ALM65
Chamber Temp Deviation - ALM65
Chamber Undertemp - ALM66
Chemical Indicator Issue - Nonalm66
Control Data CRC Error - ALM67
Cup Empty - ALM67
Cup Expired - ALM67
Cup Invalid68
Cup Read Error - ALM68
Cup Receiver Door Works Improperly - Nonalm68
Cup Receiver Open - ALM69
Date/Time Problem - Nonalm69
Display Not Working - Nonalm69
Door Issue - Nonalm70
Door Open - ALM70
Door Open too Long - ALM70
Door Unlocked - ALM71
Draw Tube Switch Failure - ALM71
Failure Reading PT1 - ALM71
Failure Reading PT2 - ALM72
Failure Reading RTD1 - ALM72
Failure Reading RTD2 - ALM72
Failure Reading RTD3 - ALM72
Failure Reading RTD4 - ALM73
File Write Error - ALM73
Injection Limit Reached73
Inject Switch Failure - ALM74
I/O Board Communication Failure - ALM74
Leak Test Failure - ALM74
Load too Wet - ALM75
LS10 Switch Failure - ALM75
LS11 Switch Failure - ALM76
LS12 Switch Failure - ALM76
Memory Read Error - ALM76
Memory Write Error - ALM77
No Power - Nonalm77
Odor or Oil Misting from Unit - Nonalm77
Oil Leak - Nonalm77
Power Failure - ALM78
Pressure Rise High - ALM78
Pressure Rise Low - ALM79
Printer Does Not Print - Nonalm79
Printer Failure - ALM80
Real Time Clock Failure - ALM80
Reservoir Overfill - ALM81
Scanner Failure81
Software Reboot81
Too Long to Air Break - ALM82
Too Long to Charge (Air Compressor) - ALM82
Too Long to Evacuate - ALM83
Too Long to Extend Tube - ALM84
Too Long to Fill (Reservoir) - ALM84
Too Long to Heat Chamber - ALM85
Too Long to Heat Vapor - ALM85
Too Long to Inject - ALM86
Too Long to Inject Fill - ALM86
Too Long to Lock Door - ALM87
Too Long to Retract Tube - ALM87
Too Long to Unlock Door - ALM87
Unit Does Not Alarm When Cup Is Empty - Nonalm88
Unit Not Calibrated - ALM88
Vaporizer Overtemp - ALM88
Vaporizer Temp Deviation - ALM89
Vaporizer Undertemp - ALM89
Routine Maintenance90
Introduction90
Read before Performing Routine Maintenance90
Routine Operator Maintenance91
Cleaning Sterilization System91
Leak Test94
Change Printer Paper Roll96
Preventive Maintenance Schedule98
Vacuum Pump Maintenance Indicator99
Replacement Parts100
Printouts102
Cleaning, Rinsing and Drying111
Packaging and Loading112
Appendix B (Supervisor Screens)119

Steris V-PRO maX 2 - Page 58

Table of Contents

Related product manuals